wandering1
2fdc5f6dda
钩子数在两个分支上不同（master 18、v2-on-ui 26），注释里写死 18/17 会让 另一分支上的读者按错数字去核对，正是本轮文档清理里修掉的同类漂移。头部 注释改为讲规则并给分分支实测快照；run 块内那行同步改成纯 ASCII 的规则 表述，避免增删钩子后再次过期。 同时作为非文档路径的普通 push：新建分支 v2-on-ui-ci 的那次 push 没有产生 run（runner 在线且空闲，job 日志最新仍是 10-03），怀疑新建分支的 push 拿 不到变更文件集、被 paths-ignore 滤空，用这次提交验证。 验证：YAML 可解析、全部 run 块纯 ASCII、无 BOM、LF；pre-commit 对该文件 通过。
483 lines
26 KiB
YAML
483 lines
26 KiB
YAML
# Gitea Actions CI —— STM32F4-Base 持续集成
|
||
#
|
||
# 覆盖范围（**只做不依赖硬件的层**，见 docs/测试说明/测试开发标准流程.md §1/§9）：
|
||
# L0 静态门禁 = pre-commit 全部钩子（等价本地 `pre-commit run --all-files`）
|
||
# L0.5 主机侧纯逻辑单测 = test/host/**（MSVC 离线编译，零硬件）
|
||
#
|
||
# ⛔ L1 板端套件（test/board/，需真机 + ST-LINK）/ L2 @test 闭环 / L3 人工目检
|
||
# **不上 CI** —— 需要开发板与烧录器，只能在本地跑。
|
||
#
|
||
# 明确不做的两件事（都是刻意为之）：
|
||
# 1. `@build`（Keil UV4）—— 需本机 Keil 授权，runner 上不具备；且 L0 的 cppcheck +
|
||
# 代码规范已覆盖"编译前的静态问题"，真编译仍是开发者的本地红线（AGENTS.md）。
|
||
# 2. `mem-numbers` 钩子 —— 它的事实源是 `MDK-ARM/**/*.map`（Keil 构建产物、已 gitignore），
|
||
# 无 `@build` 即无 `.map`。故本 workflow 在**检测不到 .map 时自动跳过该钩子**
|
||
# （见下方 "决定跳过哪些钩子" 步骤），有 .map 的 runner（如自建带 Keil 的机器）则照常跑。
|
||
#
|
||
# 🔴 门禁盲区声明（S14，2026-10-02）：跳过 `mem-numbers` 意味着 **CI 不守 Flash/RAM 体积门禁**。
|
||
# 体积变更（新增任务/缓冲/代码）不会在 CI 被拦下；必须靠**本地 `@build` 后**
|
||
# `python scripts/check_mem_numbers.py --scan` 兜底。故该跳过以 `::warning::` 明示
|
||
# （不是弱化的 `::notice::`），并写入 job step-summary 的醒目行。
|
||
#
|
||
# 产物存档（S3，2026-10-02）：两个 job 把关键输出 `Tee-Object` 到 `ci-artifacts/*.log`，
|
||
# 并写 $GITHUB_STEP_SUMMARY（Gitea UI 直接可见）+ `::notice::` 汇总行。
|
||
# **刻意不用 `actions/upload-artifact`**——内网可能拉不到外层 action（见 docs/CI/远程CI完整指南.md §5.3）；
|
||
# 零依赖方案下日志留在 runner 工作区，UI 通过 step-summary 即可排障。
|
||
# ⚠️ `ci-artifacts/` 已 gitignore（运行时产物）。
|
||
#
|
||
# 触发：push（除纯文档路径外）与 pull_request。
|
||
#
|
||
# 🔴 shell 用 `powershell` 而非 `pwsh`（2026-10-02 实测修正）：
|
||
# `pwsh` = PowerShell 7，**不是 Windows 自带**；本机 runner 只有
|
||
# Windows PowerShell 5.1（`C:\Windows\System32\WindowsPowerShell\v1.0\`），
|
||
# 用 `shell: pwsh` 会直接报 `Cannot find: pwsh in PATH` → job 失败（跑不到任何业务逻辑）。
|
||
# `shell: powershell` 在任意 Windows 上都存在。
|
||
#
|
||
# 🔴🔴 `run:` 脚本内容必须【纯 ASCII】（2026-10-02 第二次实测修正）：
|
||
# runner 把每个 `run:` 块写入临时 `.ps1`（`...\act\workflow\N.ps1`）再交给
|
||
# Windows PowerShell 5.1 执行，而该临时文件**无 BOM** → PS 5.1 按 **GBK/CP936** 解码。
|
||
# 脚本里的 UTF-8 中文字节会与相邻引号错位 → 报
|
||
# `TerminatorExpectedAtEndOfString` / `字符串缺少终止符: "` / `缺少右"}"`
|
||
# （报错行号正是含中文的那一行，极易误判为逻辑错误）。
|
||
# **故本文件所有 `run:` 块内零非 ASCII**（中文仅出现在 YAML 的 name:/注释里——
|
||
# 那些由 Gitea 按 UTF-8 读，不喂给 PowerShell，安全）。
|
||
# ⚠️ 与 AGENTS.md「字符串字面量必须纯 ASCII」同源；改脚本时务必守住。
|
||
#
|
||
# 🔴🔴 工具链探测必须【可离线自测 + 保留机器级安装兜底】（2026-10-11 第三次实测修正）：
|
||
# `33a4aa4`（DTU_* 变量改造）把 Python 探测内联进本文件，并把候选**收窄成两个**
|
||
# （PATH python + 仓库 .venv）——而 runner 上这两个都是死路：
|
||
# · SYSTEM 账号的 PATH python = `C:\msys64\ucrt64\bin\python.exe`，**没有** pre-commit；
|
||
# · 仓库 `.venv` 已 gitignore，runner 的全新工作区里**根本不存在**。
|
||
# 唯一可用的机器级解释器（`C:\ProgramData\anaconda3\python.exe`）不再被探测，而文档
|
||
# 要求的机器级 `DTU_PRECOMMIT_PYTHON` 从未设置（Machine 作用域一个 DTU_* 都没有）
|
||
# → run 14/15 的 L0 **全部死在"环境自检"，一个钩子都没跑**。cppcheck 同理：
|
||
# 旧写法"不在 PATH 就把 C:\Program Files\Cppcheck 加进 PATH"的兜底也被删了。
|
||
# **故探测逻辑搬进 `scripts/ci_find_python.ps1`**（两个 job 共用、可离线跑、失败时
|
||
# 打印全部候选），并恢复常见机器级安装位置兜底；`DTU_*` 仍是最高优先级、
|
||
# 且"显式设置就必须有效、不静默回退"的语义不变。
|
||
#
|
||
# 🔴 gitlint 属 commit-msg stage，`--all-files` **永远跑不到它**（2026-10-11 审计）：
|
||
# `.pre-commit-config.yaml` 里 gitlint 那一条**永远不进 CI 报告**（报告数 = 定义数 − 1；
|
||
# 2026-10-12 实测 `master` 18 定义 / 17 报告、`v2-on-ui` 26 定义 / 25 报告）——
|
||
# 缺的正是 gitlint：`stages: [commit-msg]` 写在 **gitlint 上游的 .pre-commit-hooks.yaml**
|
||
# 里（项目配置里 grep 不到这一行），而 `pre-commit run --all-files` 只跑 pre-commit stage。
|
||
# 即 AGENTS.md 的"单行中文标题 ≤100 字符"门禁**本地有、CI 无**，
|
||
# 且表现为"全绿"而非失败，所以一直没人发现。现由 `scripts/ci_gitlint_range.ps1`
|
||
# 逐条校验本次 push/PR 引入的提交（消息文件必须写在**仓库内**且 **UTF-8 无 BOM**：
|
||
# 跨盘符会被 pre-commit 拒绝 `path is on mount 'C:', start on mount 'D:'`，
|
||
# BOM 会占掉标题 1 个字符、扭曲 100 上限）。
|
||
#
|
||
# 🔴 写 `GITHUB_ENV` / `GITHUB_PATH` / `GITHUB_OUTPUT` 必须显式 `-Encoding ascii`
|
||
# （2026-10-11 实测）：PS 5.1 的 `Out-File -Append` **默认 UTF-16LE**——往 runner
|
||
# 用 UTF-8 建的同一个文件里追加，落盘就是 `B\x00B\x00B\x00=\x001\x00` 这种带 NUL 的行
|
||
# （实测字节：`42 00 42 00 42 00 3D 00 31 00`）。本文件写入的这些键值全是 ASCII，
|
||
# 故统一显式 ascii；`GITHUB_STEP_SUMMARY` 是 Markdown，保持 utf8。
|
||
#
|
||
# ⚠️ 前置（部署到 Gitea 时需确认）：
|
||
# - 该 Gitea 实例已启用 Actions：`[actions] ENABLED = true`（site admin 配置）
|
||
# - 已注册一个 **Windows** runner（labels 含 `windows`），且装有：
|
||
# Python 3.x、cppcheck、pre-commit、MSVC（VS2019/2022 的 C++ 工具链 + Windows SDK）
|
||
# - 缺 MSVC 时 L0.5 步骤会**降级为提示并跳过**（不硬失败），但会打印醒目 WARNING
|
||
#
|
||
# 🔧 runner 机器级环境变量（可选项覆盖；runner 以 SYSTEM 服务运行，用户级变量不可见）：
|
||
# DTU_PRECOMMIT_PYTHON / DTU_CPPCHECK / DTU_MSVC_CL —— 未设置时按 PATH / 标准 VS 布局自动发现。
|
||
# 变量显式设置但值无效时 job 直接报变量名并失败（不静默回退）。配置方法见
|
||
# docs/环境与部署/本地工具路径环境变量方案.md §5.3。
|
||
#
|
||
# 本地等价命令（与 CI 同一套判定，见 scripts/ci_local.py）：
|
||
# & '.venv\Scripts\python.exe' scripts/ci_local.py
|
||
|
||
name: CI
|
||
|
||
on:
|
||
push:
|
||
branches: ['**']
|
||
paths-ignore:
|
||
- 'docs/**'
|
||
- '**/*.md'
|
||
- '.workbuddy-ai/**'
|
||
pull_request:
|
||
paths-ignore:
|
||
- 'docs/**'
|
||
- '**/*.md'
|
||
- '.workbuddy-ai/**'
|
||
workflow_dispatch:
|
||
|
||
# 同一分支的旧运行自动取消，省 runner
|
||
concurrency:
|
||
group: ci-${{ github.ref }}
|
||
cancel-in-progress: true
|
||
|
||
jobs:
|
||
# ------------------------------------------------------------------
|
||
# L0：静态门禁（pre-commit 钩子全集）
|
||
# ------------------------------------------------------------------
|
||
l0-gates:
|
||
name: L0 静态门禁 (pre-commit)
|
||
runs-on: windows
|
||
steps:
|
||
- uses: actions/checkout@v4
|
||
with:
|
||
# 钩子要对比基线与历史（doc-links 等读工作区即可，但 gitlint/cubemx 需完整历史）
|
||
fetch-depth: 0
|
||
|
||
- name: 环境自检（Python / cppcheck / pre-commit）
|
||
shell: powershell
|
||
run: |
|
||
# NOTE: keep every run: block pure ASCII. The runner writes this block
|
||
# to a BOM-less .ps1 executed by Windows PowerShell 5.1, which decodes
|
||
# it as GBK -- non-ASCII bytes there break string quoting.
|
||
# --- pick a Python that actually has pre-commit -------------------
|
||
# Discovery lives in scripts/ci_find_python.ps1 so that
|
||
# * both jobs share ONE implementation,
|
||
# * it can be run (and its failure list inspected) offline,
|
||
# * the well-known machine-wide install locations stay probed.
|
||
# The previous inline 2-candidate probe is what killed every L0 run
|
||
# since 33a4aa4 -- see the file header.
|
||
#
|
||
# The script prints diagnostics with Write-Host and emits ONLY the
|
||
# chosen path on the success stream, so capturing it is exact.
|
||
# It also appends PYTHON=<path> to GITHUB_ENV (as ASCII) for later
|
||
# steps, which is why $env:PYTHON works in the steps below.
|
||
$py = & './scripts/ci_find_python.ps1' -NeedPreCommit -WriteEnv
|
||
if ($LASTEXITCODE -ne 0) { exit $LASTEXITCODE }
|
||
if (-not $py) {
|
||
Write-Host "::error::ci_find_python.ps1 succeeded but returned no path"
|
||
exit 2
|
||
}
|
||
$py = "$py".Trim()
|
||
|
||
# --- cppcheck -----------------------------------------------------
|
||
# Order: DTU_CPPCHECK (explicit; invalid = hard error, no fallback)
|
||
# -> PATH -> the standard install directory.
|
||
#
|
||
# The directory fallback is NOT cosmetic: the runner service runs as
|
||
# SYSTEM, whose PATH has no Cppcheck entry (a USER-scope PATH entry is
|
||
# invisible to it), and no machine-level DTU_CPPCHECK is set on a
|
||
# stock runner. Dropping this fallback in 33a4aa4 is what made L0 die
|
||
# on cppcheck as well, right after the Python probe had been fixed.
|
||
$found = $null
|
||
$envCpp = $env:DTU_CPPCHECK
|
||
if ($envCpp) {
|
||
if (-not (Test-Path $envCpp)) {
|
||
Write-Host "::error::DTU_CPPCHECK is set but does not exist: $envCpp"
|
||
Write-Host "::error::fix the variable (full path to cppcheck.exe), or unset it to use auto-discovery"
|
||
exit 1
|
||
}
|
||
$found = $envCpp
|
||
Write-Host "using cppcheck from DTU_CPPCHECK: $found"
|
||
} else {
|
||
$cmd = Get-Command cppcheck -ErrorAction SilentlyContinue
|
||
if ($cmd) {
|
||
$found = $cmd.Source
|
||
Write-Host "found cppcheck on PATH: $found"
|
||
} else {
|
||
$pf = $env:ProgramFiles
|
||
$pf86 = ${env:ProgramFiles(x86)}
|
||
if (-not $pf) { $pf = 'C:\Program Files' }
|
||
if (-not $pf86) { $pf86 = 'C:\Program Files (x86)' }
|
||
foreach ($cand in @(
|
||
(Join-Path $pf 'Cppcheck\cppcheck.exe'),
|
||
(Join-Path $pf86 'Cppcheck\cppcheck.exe'))) {
|
||
if (Test-Path $cand) { $found = $cand; break }
|
||
}
|
||
}
|
||
}
|
||
if (-not $found) {
|
||
Write-Host "::error::runner missing cppcheck (not on SYSTEM PATH, not in the standard install dir)"
|
||
Write-Host "::error::set a machine-level DTU_CPPCHECK (see scripts/ci_runner_bootstrap.ps1 -SetEnv) or add its directory to the machine PATH, then re-run"
|
||
exit 1
|
||
}
|
||
$cppDir = Split-Path -Parent $found
|
||
$env:Path = "$env:Path;$cppDir"
|
||
# ASCII on purpose: Out-File's PS 5.1 default is UTF-16LE, and other
|
||
# steps append to this same file -- mixed encodings corrupt it.
|
||
$cppDir | Out-File -FilePath $env:GITHUB_PATH -Append -Encoding ascii
|
||
& $found --version 2>&1 | Out-Host
|
||
|
||
Write-Host "runner environment check passed"
|
||
|
||
- name: 安装 pre-commit 钩子到本仓库
|
||
shell: powershell
|
||
run: "& $env:PYTHON -s -m pre_commit install --install-hooks"
|
||
|
||
- name: 提交信息门禁（gitlint，commit-msg stage）
|
||
shell: powershell
|
||
env:
|
||
DTU_BASE_SHA: ${{ github.event.before }}
|
||
DTU_PR_BASE_SHA: ${{ github.event.pull_request.base.sha }}
|
||
DTU_HEAD_SHA: ${{ github.sha }}
|
||
run: |
|
||
# Pure ASCII only (see file header).
|
||
#
|
||
# WHY THIS STEP EXISTS: gitlint is a `commit-msg` stage hook, and
|
||
# `pre-commit run --all-files` only runs the `pre-commit` stage -- so
|
||
# the commit-message rule was enforced locally and NEVER here, while
|
||
# the job still reported green: the reported hook count is always
|
||
# (defined count - 1), so a silently missing hook is invisible.
|
||
# Recount that difference whenever hooks are added or removed.
|
||
# pre-commit has no notion of "the commits of this push", so the
|
||
# script feeds each commit message to the hook one at a time.
|
||
#
|
||
# Range: PR -> base..head; push -> event.before..sha, falling back to
|
||
# the newest commits when `before` is all-zero (new branch) or
|
||
# unreachable (force push). Merge commits are skipped (git writes them).
|
||
$base = $env:DTU_PR_BASE_SHA
|
||
if (-not $base) { $base = $env:DTU_BASE_SHA }
|
||
& './scripts/ci_gitlint_range.ps1' -BaseSha $base -HeadSha $env:DTU_HEAD_SHA `
|
||
-MaxCommits 50 -PythonExe $env:PYTHON
|
||
if ($LASTEXITCODE -ne 0) {
|
||
Write-Host "::error::commit message gate failed (gitlint) -- see the per-commit output above"
|
||
exit $LASTEXITCODE
|
||
}
|
||
|
||
- name: 决定跳过哪些钩子（Keil 依赖）
|
||
id: skip
|
||
shell: powershell
|
||
run: |
|
||
# mem-numbers fact source is the Keil build artifact .map (gitignored).
|
||
# No .map => this hook cannot run => skip (not "pass", but "not applicable").
|
||
#
|
||
# S14 (2026-10-02): make this GAP loud. mem-numbers is the ONLY gate that
|
||
# checks docs/memory numbers against the real .map (Flash/RAM size). When
|
||
# it is skipped, CI effectively does NOT guard the size budget -- a silent
|
||
# ::notice:: was too easy to miss. So:
|
||
# - emit ::warning:: (not ::notice::) so it shows in the run summary
|
||
# - write a machine-readable marker file for the summary step
|
||
# - append a bold line to the job step-summary
|
||
$map = Get-ChildItem -Path 'MDK-ARM' -Recurse -Filter '*.map' -ErrorAction SilentlyContinue
|
||
if ($map) {
|
||
Write-Host "found .map: $($map[0].FullName) -- mem-numbers runs normally"
|
||
"value=" | Out-File -FilePath $env:GITHUB_OUTPUT -Append -Encoding ascii
|
||
"sizegate=on" | Out-File -FilePath $env:GITHUB_OUTPUT -Append -Encoding ascii
|
||
"> Volume gate (mem-numbers): RAN (.map present)" |
|
||
Out-File -FilePath $env:GITHUB_STEP_SUMMARY -Append -Encoding utf8
|
||
} else {
|
||
Write-Host "::warning::no .map found (no Keil build) -- SKIPPING mem-numbers, so the Flash/RAM size gate does NOT run in CI. Size changes are NOT caught here; verify locally with 'python scripts/check_mem_numbers.py --scan' after a Keil build."
|
||
"value=mem-numbers" | Out-File -FilePath $env:GITHUB_OUTPUT -Append -Encoding ascii
|
||
"sizegate=off" | Out-File -FilePath $env:GITHUB_OUTPUT -Append -Encoding ascii
|
||
"> :warning: Volume gate (mem-numbers): **NOT RUN** -- no `.map` (no Keil build)." |
|
||
Out-File -FilePath $env:GITHUB_STEP_SUMMARY -Append -Encoding utf8
|
||
}
|
||
|
||
- name: 运行 L0 门禁（--all-files）
|
||
shell: powershell
|
||
env:
|
||
SKIP: ${{ steps.skip.outputs.value }}
|
||
run: |
|
||
# Pure ASCII only (see file header). Capture output to an artifact file
|
||
# AND to the console (Tee-Object), so a failed run is debuggable from the
|
||
# Gitea UI without inspecting runner disk.
|
||
#
|
||
# CAUTION: the runner injects $ErrorActionPreference='Stop'. With `2>&1 |`,
|
||
# a native command's stderr becomes an ErrorRecord -> under 'Stop' that
|
||
# would ABORT the pipeline. Relax the preference around the pipeline and
|
||
# restore it afterwards (same pattern as the env-check step above).
|
||
New-Item -ItemType Directory -Force -Path 'ci-artifacts' | Out-Null
|
||
$log = 'ci-artifacts\l0-pre-commit.log'
|
||
if ($env:SKIP) { Write-Host "SKIP=$env:SKIP" }
|
||
$saved = $ErrorActionPreference
|
||
$ErrorActionPreference = 'Continue'
|
||
& $env:PYTHON -s -m pre_commit run --all-files --show-diff-on-failure 2>&1 |
|
||
Tee-Object -FilePath $log
|
||
$rc = $LASTEXITCODE
|
||
$ErrorActionPreference = $saved
|
||
|
||
# Summarize hook results: count Passed / Failed / Skipped lines.
|
||
$lines = Get-Content $log -ErrorAction SilentlyContinue
|
||
$passed = @($lines | Select-String -Pattern 'Passed$').Count
|
||
$failed = @($lines | Select-String -Pattern 'Failed$').Count
|
||
$skipd = @($lines | Select-String -Pattern 'Skipped$').Count
|
||
$summary = "L0: pre-commit hooks -- passed=$passed failed=$failed skipped=$skipd (log: $log)"
|
||
Write-Host "::notice::$summary"
|
||
Add-Content -Path $env:GITHUB_STEP_SUMMARY -Value "### L0 static gates" -Encoding utf8
|
||
Add-Content -Path $env:GITHUB_STEP_SUMMARY -Value $summary -Encoding utf8
|
||
|
||
if ($rc -ne 0) {
|
||
Write-Host "::error::L0 static gates failed (see output above and $log)"
|
||
exit $rc
|
||
}
|
||
|
||
- name: 归档 L0 日志（供下载/排障）
|
||
if: always()
|
||
shell: powershell
|
||
run: |
|
||
# S3: zero-dependency artifact archival. We do NOT use
|
||
# actions/upload-artifact (inner networks may not fetch outer actions);
|
||
# instead we keep the log on the runner AND surface its path + tail in
|
||
# the step summary, so the UI is self-sufficient for triage.
|
||
if (Test-Path 'ci-artifacts\l0-pre-commit.log') {
|
||
$size = (Get-Item 'ci-artifacts\l0-pre-commit.log').Length
|
||
Write-Host "archived: ci-artifacts/l0-pre-commit.log ($size bytes)"
|
||
Add-Content -Path $env:GITHUB_STEP_SUMMARY -Value "" -Encoding utf8
|
||
Add-Content -Path $env:GITHUB_STEP_SUMMARY -Value "Archived log: ``ci-artifacts/l0-pre-commit.log`` ($size bytes on runner)" -Encoding utf8
|
||
}
|
||
Write-Host "::notice::L0 artifacts kept on runner at: ci-artifacts\l0-pre-commit.log"
|
||
|
||
# ------------------------------------------------------------------
|
||
# L0.5：主机侧纯逻辑单测（零硬件；缺 MSVC 则跳过）
|
||
# ------------------------------------------------------------------
|
||
l05-host-unit-tests:
|
||
name: L0.5 主机侧单测 (MSVC)
|
||
runs-on: windows
|
||
steps:
|
||
- uses: actions/checkout@v4
|
||
|
||
- name: 探测 MSVC（VS BuildTools / Community 等）
|
||
id: msvc
|
||
shell: powershell
|
||
run: |
|
||
# MSVC discovery per the DTU_* plan, kept in sync with
|
||
# test/host/common/unit_test_harness.py:
|
||
# DTU_MSVC_CL (explicit x64 cl.exe; invalid = hard error)
|
||
# -> auto-probe standard VS roots derived from %ProgramFiles%
|
||
# / %ProgramFiles(x86)% (2019 / 2022 / 2026, all editions)
|
||
$found = $false
|
||
$envCl = $env:DTU_MSVC_CL
|
||
if ($envCl) {
|
||
if (-not (Test-Path $envCl)) {
|
||
Write-Host "::error::DTU_MSVC_CL is set but does not exist: $envCl"
|
||
exit 1
|
||
}
|
||
if ($envCl -notlike '*bin\Hostx64\x64\cl.exe') {
|
||
Write-Host "::error::DTU_MSVC_CL must be the x64 Host compiler (path ending bin\Hostx64\x64\cl.exe): $envCl"
|
||
exit 1
|
||
}
|
||
$found = $true
|
||
Write-Host "using cl.exe from DTU_MSVC_CL: $envCl"
|
||
} else {
|
||
$pf = ${env:ProgramFiles}
|
||
$pf86 = ${env:ProgramFiles(x86)}
|
||
if (-not $pf) { $pf = 'C:\Program Files' }
|
||
if (-not $pf86) { $pf86 = 'C:\Program Files (x86)' }
|
||
$roots = @(
|
||
(Join-Path $pf86 'Microsoft Visual Studio\2019\BuildTools'),
|
||
(Join-Path $pf86 'Microsoft Visual Studio\2019\Community'),
|
||
(Join-Path $pf86 'Microsoft Visual Studio\2019\Professional'),
|
||
(Join-Path $pf 'Microsoft Visual Studio\2022\BuildTools'),
|
||
(Join-Path $pf 'Microsoft Visual Studio\2022\Community'),
|
||
(Join-Path $pf 'Microsoft Visual Studio\2022\Professional'),
|
||
(Join-Path $pf 'Microsoft Visual Studio\2022\Enterprise'),
|
||
(Join-Path $pf 'Microsoft Visual Studio\2026\BuildTools'),
|
||
(Join-Path $pf 'Microsoft Visual Studio\2026\Community'),
|
||
(Join-Path $pf 'Microsoft Visual Studio\18\BuildTools'),
|
||
(Join-Path $pf 'Microsoft Visual Studio\18\Community'),
|
||
(Join-Path $pf 'Microsoft Visual Studio\18\Professional'),
|
||
(Join-Path $pf 'Microsoft Visual Studio\18\Enterprise')
|
||
)
|
||
foreach ($r in $roots) {
|
||
if (Test-Path $r) {
|
||
$cl = Get-ChildItem -Path $r -Recurse -Filter 'cl.exe' -ErrorAction SilentlyContinue |
|
||
Where-Object { $_.FullName -like '*Hostx64\x64*' } | Select-Object -First 1
|
||
if ($cl) { $found = $true; Write-Host "found cl.exe: $($cl.FullName)"; break }
|
||
}
|
||
}
|
||
}
|
||
if ($found) {
|
||
"value=yes" | Out-File -FilePath $env:GITHUB_OUTPUT -Append -Encoding ascii
|
||
} else {
|
||
Write-Host "::warning::runner has no MSVC (VS C++ toolchain) -- skipping L0.5. Install VS BuildTools and re-run."
|
||
"value=no" | Out-File -FilePath $env:GITHUB_OUTPUT -Append -Encoding ascii
|
||
}
|
||
|
||
- name: 运行主机侧单测
|
||
id: l05
|
||
if: steps.msvc.outputs.value == 'yes'
|
||
shell: powershell
|
||
run: |
|
||
# Resolve a working Python with the SAME shared probe as L0 (no
|
||
# -NeedPreCommit: these harnesses are stdlib-only). The old inline
|
||
# probe here had the same 2-candidate blind spot as L0 -- it only
|
||
# survived by luck, because the stdlib tests also run on the msys64
|
||
# python that happens to be on SYSTEM's PATH.
|
||
$py = & './scripts/ci_find_python.ps1' -WriteEnv
|
||
if ($LASTEXITCODE -ne 0) { exit $LASTEXITCODE }
|
||
if (-not $py) {
|
||
Write-Host "::error::ci_find_python.ps1 succeeded but returned no path"
|
||
exit 2
|
||
}
|
||
$py = "$py".Trim()
|
||
Write-Host "using python: $py"
|
||
|
||
New-Item -ItemType Directory -Force -Path 'ci-artifacts' | Out-Null
|
||
|
||
# Iterate test/host/*/run_unit_test.py (each module ships its own runner via common harness)
|
||
$runners = Get-ChildItem -Path 'test/host' -Recurse -Filter 'run_unit_test.py' |
|
||
Sort-Object FullName
|
||
if (-not $runners) {
|
||
Write-Host "::warning::no test/host/**/run_unit_test.py found -- skipping"
|
||
exit 0
|
||
}
|
||
$fail = 0
|
||
$runnerCount = 0
|
||
$sumPass = 0
|
||
$sumTotal = 0
|
||
# Relax preference around each `2>&1 | Tee-Object` pipeline (native stderr
|
||
# becomes ErrorRecord -> 'Stop' would abort). See L0 step for details.
|
||
$savedPref = $ErrorActionPreference
|
||
foreach ($r in $runners) {
|
||
$runnerCount++
|
||
$name = $r.Directory.Name
|
||
$log = "ci-artifacts\l05-$name.log"
|
||
Write-Host "================================"
|
||
Write-Host "run: $($r.FullName)"
|
||
Write-Host "================================"
|
||
$ErrorActionPreference = 'Continue'
|
||
& $py $r.FullName 2>&1 | Tee-Object -FilePath $log
|
||
$rc = $LASTEXITCODE
|
||
$ErrorActionPreference = $savedPref
|
||
|
||
# Parse the module's own summary line, e.g.
|
||
# "=== System Clock Tests: 100/100 PASSED (failed=0) ==="
|
||
$m = Select-String -Path $log -Pattern ': (\d+)/(\d+) PASSED \(failed=(\d+)\)' -ErrorAction SilentlyContinue |
|
||
Select-Object -Last 1
|
||
if ($m) {
|
||
$sumPass += [int]$m.Matches[0].Groups[1].Value
|
||
$sumTotal += [int]$m.Matches[0].Groups[2].Value
|
||
Write-Host ("::notice::{0}: {1}" -f $name, $m.Matches[0].Value.Trim())
|
||
} else {
|
||
Write-Host "::warning::$name produced no '=== ... N/M PASSED ===' summary line"
|
||
}
|
||
if ($rc -ne 0) {
|
||
Write-Host "::error::unit test failed: $($r.FullName) (exit $rc)"
|
||
$fail = 1
|
||
}
|
||
}
|
||
|
||
$agg = "L0.5: $runnerCount runner(s), $sumPass/$sumTotal assertions passed, fail=$fail"
|
||
Write-Host "::notice::$agg"
|
||
Add-Content -Path $env:GITHUB_STEP_SUMMARY -Value "### L0.5 host-side unit tests" -Encoding utf8
|
||
Add-Content -Path $env:GITHUB_STEP_SUMMARY -Value $agg -Encoding utf8
|
||
"count=$runnerCount" | Out-File -FilePath $env:GITHUB_OUTPUT -Append -Encoding ascii
|
||
"agg=$agg" | Out-File -FilePath $env:GITHUB_OUTPUT -Append -Encoding ascii
|
||
exit $fail
|
||
|
||
- name: 归档 L0.5 日志（供下载/排障）
|
||
if: always()
|
||
shell: powershell
|
||
run: |
|
||
# S3: same zero-dependency archival as L0.
|
||
if (Test-Path 'ci-artifacts') {
|
||
$logs = Get-ChildItem -Path 'ci-artifacts' -Filter '*.log' -ErrorAction SilentlyContinue
|
||
foreach ($f in $logs) {
|
||
Write-Host "archived: $($f.FullName) ($($f.Length) bytes)"
|
||
}
|
||
$names = ($logs | ForEach-Object { '``' + $_.Name + '``' }) -join ', '
|
||
if ($names) {
|
||
Add-Content -Path $env:GITHUB_STEP_SUMMARY -Value "" -Encoding utf8
|
||
Add-Content -Path $env:GITHUB_STEP_SUMMARY -Value "Archived logs on runner: $names" -Encoding utf8
|
||
}
|
||
} else {
|
||
Write-Host "no ci-artifacts directory (L0.5 skipped or failed early)"
|
||
}
|
||
|
||
- name: L0.5 跳过说明
|
||
if: steps.msvc.outputs.value == 'no'
|
||
shell: powershell
|
||
run: |
|
||
Write-Host "L0.5 skipped: runner has no MSVC."
|
||
Write-Host "Local equivalent: & '.venv\Scripts\python.exe' scripts/ci_local.py"
|
||
Add-Content -Path $env:GITHUB_STEP_SUMMARY -Value "### L0.5 host-side unit tests" -Encoding utf8
|
||
Add-Content -Path $env:GITHUB_STEP_SUMMARY -Value ":warning: **NOT RUN** -- runner has no MSVC (VS C++ toolchain)." -Encoding utf8
|
||
exit 0
|