feat(ui): fold board inputs and outputs into the telemetry page
The 12 board-level rows now live at the end of the 遥信量 page instead of a separate 开入开出 page: 8 opto inputs (DI_A..DI_H) and 4 relay outputs (KO6/TRIP/ERT/CLZ). 33 rows become 45, five pages become six. The standalone page, its menu entry, its golden references and both build registrations are removed. Folding the display is not folding the point table. The board rows render from dio_di_* / dio_do_* and stay out of yx_bits / yx_valid / yx_dp: any change to those carriers is provably absent from this diff. IEC 104 mapping and YX_VALID_MASK are untouched, so nothing new is reported to a master station. Input polarity was wrong and is fixed here. On this board a 24 V input drives the opto, which pulls the 74HC165 pin LOW, so the raw mask is inverted relative to "has signal". The bit assembly only reordered bits; nothing converted the level. The screen showed 分 on every channel no matter what the operator drove in. Polarity now converts once, in the driver, behind IOBOARD_DI_LEVEL_ACTIVE (0 = active low), so callers see 1 = has signal for both inputs and outputs. Verified on the board: page 5 shows YX33 followed immediately by DI_A, crossing the 33-point boundary with no drift; DI_C reads 合 because the operator's signal is on channel C, the other seven read 分; page 6 shows DI_H then all four outputs 释放. Page rows end at y=134, the footer starts at y=144. Input bit order is only partly verified: channel C was confirmed against a real signal, the other seven have not been exercised channel by channel. The board detects the presence of 24 V, not contact closure, and the output rows show the shadow register (our intent) rather than mechanical contact feedback. All three limits are recorded in the page header and in the IOBOARD README. Also adds a polarity guard to the host tests: the input polarity was flipped once already, and until now no assertion would have caught a silent re-flip, since only the DO side was pinned.
This commit is contained in:
@@ -18,44 +18,43 @@ const ui_menu_node_t g_menu_tab[UI_MENU_TAB_COUNT] = {
|
||||
{ 2, 0u, "交流量" }, /* 3 二级菜单 */
|
||||
{ 2, 0u, "直流量" }, /* 4 二级菜单 */
|
||||
{ 2, 0u, "遥信量" }, /* 5 二级菜单 */
|
||||
{ 2, 0u, "开入开出" }, /* 6 二级菜单 */
|
||||
{ 0, 0u, "参数定值" }, /* 7 一级菜单 */
|
||||
{ 7, 0u, "整定" }, /* 8 二级菜单 */
|
||||
{ 8, 1u, "参数" }, /* 9 三级菜单 */
|
||||
{ 8, 1u, "定值" }, /* 10 三级菜单 */
|
||||
{ 8, 1u, "控制字" }, /* 11 三级菜单 */
|
||||
{ 8, 1u, "软压板" }, /* 12 三级菜单 */
|
||||
{ 7, 0u, "查看" }, /* 13 二级菜单 */
|
||||
{ 13, 0u, "参数" }, /* 14 三级菜单 */
|
||||
{ 13, 0u, "定值" }, /* 15 三级菜单 */
|
||||
{ 13, 0u, "控制字" }, /* 16 三级菜单 */
|
||||
{ 13, 0u, "软压板" }, /* 17 三级菜单 */
|
||||
{ 0, 0u, "三遥设置" }, /* 18 一级菜单 */
|
||||
{ 18, 1u, "遥测死区" }, /* 19 二级菜单 */
|
||||
{ 18, 1u, "遥测系数" }, /* 20 二级菜单 */
|
||||
{ 18, 1u, "遥信类型" }, /* 21 二级菜单 */
|
||||
{ 18, 1u, "遥信防抖" }, /* 22 二级菜单 */
|
||||
{ 18, 1u, "双点遥信" }, /* 23 二级菜单 */
|
||||
{ 0, 0u, "装置维护" }, /* 24 一级菜单 */
|
||||
{ 24, 1u, "时钟设置" }, /* 25 二级菜单 */
|
||||
{ 24, 1u, "强制复归" }, /* 26 二级菜单 */
|
||||
{ 24, 1u, "手动录波" }, /* 27 二级菜单 */
|
||||
{ 24, 1u, "清除记录" }, /* 28 二级菜单 */
|
||||
{ 0, 0u, "通讯参数" }, /* 29 一级菜单 */
|
||||
{ 29, 1u, "通讯设置" }, /* 30 二级菜单 */
|
||||
{ 29, 1u, "网口设置" }, /* 31 二级菜单 */
|
||||
{ 29, 1u, "SNTP设置" }, /* 32 二级菜单 */
|
||||
{ 0, 0u, "记录查询" }, /* 33 一级菜单 */
|
||||
{ 33, 0u, "SOE记录" }, /* 34 二级菜单 */
|
||||
{ 33, 0u, "事故记录" }, /* 35 二级菜单 */
|
||||
{ 33, 0u, "操作记录" }, /* 36 二级菜单 */
|
||||
{ 33, 0u, "保护告警" }, /* 37 二级菜单 */
|
||||
{ 33, 0u, "保护启动" }, /* 38 二级菜单 */
|
||||
{ 33, 0u, "遥控记录" }, /* 39 二级菜单 */
|
||||
{ 33, 0u, "自检记录" }, /* 40 二级菜单 */
|
||||
{ 33, 0u, "运行记录" }, /* 41 二级菜单 */
|
||||
{ 33, 0u, "运行报告" }, /* 42 二级菜单 */
|
||||
{ 33, 0u, "录波回放" }, /* 43 二级菜单 */
|
||||
{ 0, 0u, "参数定值" }, /* 6 一级菜单 */
|
||||
{ 6, 0u, "整定" }, /* 7 二级菜单 */
|
||||
{ 7, 1u, "参数" }, /* 8 三级菜单 */
|
||||
{ 7, 1u, "定值" }, /* 9 三级菜单 */
|
||||
{ 7, 1u, "控制字" }, /* 10 三级菜单 */
|
||||
{ 7, 1u, "软压板" }, /* 11 三级菜单 */
|
||||
{ 6, 0u, "查看" }, /* 12 二级菜单 */
|
||||
{ 12, 0u, "参数" }, /* 13 三级菜单 */
|
||||
{ 12, 0u, "定值" }, /* 14 三级菜单 */
|
||||
{ 12, 0u, "控制字" }, /* 15 三级菜单 */
|
||||
{ 12, 0u, "软压板" }, /* 16 三级菜单 */
|
||||
{ 0, 0u, "三遥设置" }, /* 17 一级菜单 */
|
||||
{ 17, 1u, "遥测死区" }, /* 18 二级菜单 */
|
||||
{ 17, 1u, "遥测系数" }, /* 19 二级菜单 */
|
||||
{ 17, 1u, "遥信类型" }, /* 20 二级菜单 */
|
||||
{ 17, 1u, "遥信防抖" }, /* 21 二级菜单 */
|
||||
{ 17, 1u, "双点遥信" }, /* 22 二级菜单 */
|
||||
{ 0, 0u, "装置维护" }, /* 23 一级菜单 */
|
||||
{ 23, 1u, "时钟设置" }, /* 24 二级菜单 */
|
||||
{ 23, 1u, "强制复归" }, /* 25 二级菜单 */
|
||||
{ 23, 1u, "手动录波" }, /* 26 二级菜单 */
|
||||
{ 23, 1u, "清除记录" }, /* 27 二级菜单 */
|
||||
{ 0, 0u, "通讯参数" }, /* 28 一级菜单 */
|
||||
{ 28, 1u, "通讯设置" }, /* 29 二级菜单 */
|
||||
{ 28, 1u, "网口设置" }, /* 30 二级菜单 */
|
||||
{ 28, 1u, "SNTP设置" }, /* 31 二级菜单 */
|
||||
{ 0, 0u, "记录查询" }, /* 32 一级菜单 */
|
||||
{ 32, 0u, "SOE记录" }, /* 33 二级菜单 */
|
||||
{ 32, 0u, "事故记录" }, /* 34 二级菜单 */
|
||||
{ 32, 0u, "操作记录" }, /* 35 二级菜单 */
|
||||
{ 32, 0u, "保护告警" }, /* 36 二级菜单 */
|
||||
{ 32, 0u, "保护启动" }, /* 37 二级菜单 */
|
||||
{ 32, 0u, "遥控记录" }, /* 38 二级菜单 */
|
||||
{ 32, 0u, "自检记录" }, /* 39 二级菜单 */
|
||||
{ 32, 0u, "运行记录" }, /* 40 二级菜单 */
|
||||
{ 32, 0u, "运行报告" }, /* 41 二级菜单 */
|
||||
{ 32, 0u, "录波回放" }, /* 42 二级菜单 */
|
||||
};
|
||||
|
||||
/*
|
||||
|
||||
Reference in New Issue
Block a user