KO_24V (PF4, bit6) is not an externally controllable output: it feeds
the other KO channels, so the driver now asserts it automatically
whenever any relay-class channel (bit0/1/2/3/7/8) is attracted, and
never for the three LED channels (bit4/5/9). Externally controllable
outputs become 9; physical bit map, DO_COUNT=10, DO_MASK_ALL=0x03FF,
k_do_pin[] binding, per-port BSRR segments and the uint16_t path are
unchanged.
- ioboard_do_write: clear the caller's bit6, synthesize it from
IOBOARD_DO_RELAY_MASK (0x18F), then one shadow store + one apply,
so bit6 changes in the same BSRR write as its GPIOF neighbours.
- ioboard_do_get: bit6 now reports the actual 24V supply state, not
an echo of the caller's write. Power-on release keeps PF4 low.
- board test Phase 3 derives expectations from RELAY_MASK (no second
truth table); the KO_24V row exercises "write ignored" and a new
auto-24V check verifies set-on-relay / drop-on-release.
- host contract test pins RELAY_MASK membership (excludes bit6 and
LED bits, union fills 0x3FF); 131/131 passed.
- docs: sync note v1.4 + BSP README unify the semantics (9
controllable + auto supply enable); stale "10 controllable" and
"24V interlock not implemented" wording removed; netlist-unknown
routing, PC15 backup-domain 3 mA limit and the missing auxiliary
contact remain documented as open facts.
Verified: Keil rebuild 0 error 0 warning (sizes identical to parent
wave), host unit tests 131/131, check_bsp_err / check_doc_links /
git diff --check clean. Board Phase 3 still needs a bench run.
Flat-expand the board output driver from 4 to 10 channels as decided:
IOBOARD_DO_COUNT 4->10, mask uint8_t->uint16_t, IOBOARD_DO_MASK_ALL
0x03FF. The 6 new pins keep their bit positions: KO_LED1=PF2(bit4),
KO_LED2=PF3(bit5), KO_24V=PF4(bit6), KO4=PF5(bit7), KO5=PC15(bit8),
KO_LED3=PE6(bit9); the original 4 (KO6/TRIP/ERT/CLZ) keep bit0..3.
Backups-domain PC15 is used as a signal bit only (+/-3 mA limit).
No 24V supply interlock and no LED special-casing: the driver writes
KO_24V as an ordinary bit; callers needing relay power sequencing must
assert it before energizing a channel. do_write/get/read_level and the
shadow register are all uint16_t; do_apply flushes four port segments
(GPIOC/GPIOF/GPIOC/GPIOE) and do_read_level caches three port ODRs.
UI: UI_DATA_DO_N 4->10, dio_do_mask uint16_t, UI_DATA_VER 3->4 because
dio_do_valid shifts 211->212; feed mask and dio row table extended;
content-page golden references regenerated for 51 rows / 7 pages.
Host ioboard tests 127/127 and ui_data tests 305/305 pass; Keil rebuild
0 errors 0 warnings. RAM ledger, memory snapshot and size attestation
refilled from the authoritative map. Docs: ioboard spec v1.2->v1.3 and
the resolved 6-pin question closed out.
The 12 board-level rows now live at the end of the 遥信量 page instead of
a separate 开入开出 page: 8 opto inputs (DI_A..DI_H) and 4 relay outputs
(KO6/TRIP/ERT/CLZ). 33 rows become 45, five pages become six. The
standalone page, its menu entry, its golden references and both build
registrations are removed.
Folding the display is not folding the point table. The board rows
render from dio_di_* / dio_do_* and stay out of yx_bits / yx_valid /
yx_dp: any change to those carriers is provably absent from this diff.
IEC 104 mapping and YX_VALID_MASK are untouched, so nothing new is
reported to a master station.
Input polarity was wrong and is fixed here. On this board a 24 V input
drives the opto, which pulls the 74HC165 pin LOW, so the raw mask is
inverted relative to "has signal". The bit assembly only reordered bits;
nothing converted the level. The screen showed 分 on every channel no
matter what the operator drove in. Polarity now converts once, in the
driver, behind IOBOARD_DI_LEVEL_ACTIVE (0 = active low), so callers see
1 = has signal for both inputs and outputs.
Verified on the board: page 5 shows YX33 followed immediately by DI_A,
crossing the 33-point boundary with no drift; DI_C reads 合 because the
operator's signal is on channel C, the other seven read 分; page 6 shows
DI_H then all four outputs 释放. Page rows end at y=134, the footer
starts at y=144.
Input bit order is only partly verified: channel C was confirmed against
a real signal, the other seven have not been exercised channel by
channel. The board detects the presence of 24 V, not contact closure,
and the output rows show the shadow register (our intent) rather than
mechanical contact feedback. All three limits are recorded in the page
header and in the IOBOARD README.
Also adds a polarity guard to the host tests: the input polarity was
flipped once already, and until now no assertion would have caught a
silent re-flip, since only the DO side was pinned.