Files
STM32F4-Base/test/board
wandering1 6e0755f971 feat(ioboard): make KO_24V an auto relay supply enable (9 channels)
KO_24V (PF4, bit6) is not an externally controllable output: it feeds
the other KO channels, so the driver now asserts it automatically
whenever any relay-class channel (bit0/1/2/3/7/8) is attracted, and
never for the three LED channels (bit4/5/9). Externally controllable
outputs become 9; physical bit map, DO_COUNT=10, DO_MASK_ALL=0x03FF,
k_do_pin[] binding, per-port BSRR segments and the uint16_t path are
unchanged.

- ioboard_do_write: clear the caller's bit6, synthesize it from
  IOBOARD_DO_RELAY_MASK (0x18F), then one shadow store + one apply,
  so bit6 changes in the same BSRR write as its GPIOF neighbours.
- ioboard_do_get: bit6 now reports the actual 24V supply state, not
  an echo of the caller's write. Power-on release keeps PF4 low.
- board test Phase 3 derives expectations from RELAY_MASK (no second
  truth table); the KO_24V row exercises "write ignored" and a new
  auto-24V check verifies set-on-relay / drop-on-release.
- host contract test pins RELAY_MASK membership (excludes bit6 and
  LED bits, union fills 0x3FF); 131/131 passed.
- docs: sync note v1.4 + BSP README unify the semantics (9
  controllable + auto supply enable); stale "10 controllable" and
  "24V interlock not implemented" wording removed; netlist-unknown
  routing, PC15 backup-domain 3 mA limit and the missing auxiliary
  contact remain documented as open facts.

Verified: Keil rebuild 0 error 0 warning (sizes identical to parent
wave), host unit tests 131/131, check_bsp_err / check_doc_links /
git diff --check clean. Board Phase 3 still needs a bench run.
2026-11-18 19:34:47 +08:00
..

test/board/ — 板端测试套件

⚠️ 编入固件的测试代码(由 testTask 执行)。这些 .c 已注册到 Keil 工程 MDK-ARM/STM32F4-Demo.uvprojx,占用 MCU 的 RAM/Flash。

文件一览

文件 测试对象 / 作用
test_config.c/h 测试任务配置:TEST_SUITE_* 套件选择开关(互斥)+ ENABLE_DESTRUCTIVE_TESTS
test_common.h 公共断言内核:test_stats_t + TEST_CHECK_IMPL/TEST_REPORT_IMPL;各套件用一行宏绑定自身统计变量
ch395f_test_task.c/h + ch395f_test.h CH395F 以太网(硬件层 Phase 15 / NET 层 Phase 611)
gd5f_test_task.c/h + gd5f_test.h GD5F2GQ5UE SPI NAND 存储
sd2506_test_task.c/h + sd2506_test.h SD2506 RTC
storage_test_task.c/h + storage_test.h 存储性能
net_test_task.c/h 网络层测试
net_latency_test.c/h 链路时延探针(DWT CYCCNT 时基,MCU 专属)

⚠️ 构建约束(详见本节与 test_config.h)

  • 套件互斥:test_config.h 的 TEST_SUITE_CH395F/STORAGE/GD5F/RTC 一次只能启用一个 (违反则 #error);全部注释 = 产品构建
  • ⚠️ 测试固件不得静默提交:TEST_SUITE_* 开关受 pre-commit 钩子 test-suite-switch 门禁——默认要求全部注释。跑完套件回归务必改回产品构建再提交(2026-10-01 实测已提交 HEAD 里 TEST_SUITE_CH395F 就是开启状态,纯靠人记得改;故补此门禁)。确需提交测试构建时用 ALLOW_TEST_BUILD=1 git commit ... 或 python scripts/check_test_suite.py --allow-test-build 显式放行
  • 破坏性用例默认关闭:ENABLE_DESTRUCTIVE_TESTS(默认注释)控制写/擦 NAND、格式化、 坏块注入。关闭时为只读模式(横幅 mode: READ-ONLY),可随时在在用设备上跑
  • ⚠️ 实测一轮破坏性 GD5F 运行即让 dhara 多记一个坏块(容量下降且需全片擦除恢复)—— 只在产线首启或明确需要时打开
  • CH395F 套件:硬件层与 NET 层模式互斥
  • 总线独占:CH395F 硬件层模式下 netTask 自挂起,testTask 独占 CH395F

添加新测试套件

  1. 在 test_config.h 加开关(并入互斥 #error 检查)
  2. 新建 <模块>_test_task.c/h
  3. 注册进 Keil 工程(<FilePath>..\test\board\xxx.c</FilePath>)
  4. 跑回归:/serial-boot-test(.dsh/skills/serial-boot-test/scripts/run_boot_test.py)

相关文档

  • 测试指南:docs/测试说明/板级测试/CH395F_Test_Guide.md、GD5F2GQ5UE_Test_Guide.md、SD2506_Test_Guide.md、FTP_Test_Guide.md
  • 套件配置:本节「构建约束」+ board-test-suite skill(套件互斥、破坏性开关代价、跑后恢复产品构建)
  • 容量恢复:docs/测试说明/专项验证/存储维护与容量恢复.md