Files
STM32F4-Base/simulator/CMakeLists.txt
T
wandering1 515db819ab feat(ui): fold board inputs and outputs into the telemetry page
The 12 board-level rows now live at the end of the 遥信量 page instead of
a separate 开入开出 page: 8 opto inputs (DI_A..DI_H) and 4 relay outputs
(KO6/TRIP/ERT/CLZ). 33 rows become 45, five pages become six. The
standalone page, its menu entry, its golden references and both build
registrations are removed.

Folding the display is not folding the point table. The board rows
render from dio_di_* / dio_do_* and stay out of yx_bits / yx_valid /
yx_dp: any change to those carriers is provably absent from this diff.
IEC 104 mapping and YX_VALID_MASK are untouched, so nothing new is
reported to a master station.

Input polarity was wrong and is fixed here. On this board a 24 V input
drives the opto, which pulls the 74HC165 pin LOW, so the raw mask is
inverted relative to "has signal". The bit assembly only reordered bits;
nothing converted the level. The screen showed 分 on every channel no
matter what the operator drove in. Polarity now converts once, in the
driver, behind IOBOARD_DI_LEVEL_ACTIVE (0 = active low), so callers see
1 = has signal for both inputs and outputs.

Verified on the board: page 5 shows YX33 followed immediately by DI_A,
crossing the 33-point boundary with no drift; DI_C reads 合 because the
operator's signal is on channel C, the other seven read 分; page 6 shows
DI_H then all four outputs 释放. Page rows end at y=134, the footer
starts at y=144.

Input bit order is only partly verified: channel C was confirmed against
a real signal, the other seven have not been exercised channel by
channel. The board detects the presence of 24 V, not contact closure,
and the output rows show the shadow register (our intent) rather than
mechanical contact feedback. All three limits are recorded in the page
header and in the IOBOARD README.

Also adds a polarity guard to the host tests: the input polarity was
flipped once already, and until now no assertion would have caught a
silent re-flip, since only the DO side was pinned.
2026-11-16 23:30:35 +08:00

254 lines
11 KiB
CMake
Raw Blame History

This file contains ambiguous Unicode characters
This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.
cmake_minimum_required(VERSION 3.15)
project(lvgl_sim C)
#=============================================================================
# 路径配置(相对于 simulator/ 目录)
#=============================================================================
set(PROJECT_ROOT "${CMAKE_CURRENT_SOURCE_DIR}/..")
set(LVGL_DIR "${PROJECT_ROOT}/Lib/lvgl")
set(UI_DIR "${PROJECT_ROOT}/Drivers/BSP/UI")
set(NET_DIR "${PROJECT_ROOT}/Drivers/BSP/NET")
set(NETCFG_DIR "${PROJECT_ROOT}/Drivers/BSP/NETCFG")
set(SDL2_DIR "${CMAKE_CURRENT_SOURCE_DIR}/SDL2/SDL2-2.32.10")
#=============================================================================
# 编译标准
#=============================================================================
set(CMAKE_C_STANDARD 99)
set(CMAKE_C_STANDARD_REQUIRED ON)
# Windows 控制台输出(显示 printf)
if(WIN32)
add_compile_definitions(_CRT_SECURE_NO_WARNINGS)
endif()
# MSVC:源码为 UTF-8 编码(含中文注释),强制按 UTF-8 解析消除 C4819 警告
if(MSVC)
add_compile_options(/utf-8)
endif()
#=============================================================================
# SDL2 头文件路径(需先于 add_subdirectory 定义,供 LVGL SDL 驱动使用)
#=============================================================================
# LVGL SDL 驱动内部 #include "SDL2/SDL.h",include 目录下已有 SDL2/ 子目录
set(SDL2_INCLUDE_DIR "${SDL2_DIR}/include" CACHE PATH "SDL2 include directory for LVGL")
#=============================================================================
# LVGL 子目录(引用项目自带的 LVGL v9.3.0 源码)
#=============================================================================
# LVGL 内部会自动检测 lv_conf.h(通过 LV_CONF_INCLUDE_SIMPLE 宏)
# 需要将 simulator 目录加入 LVGL 的包含路径,使其能找到 lv_conf.h
set(LV_CONF_DIR "${CMAKE_CURRENT_SOURCE_DIR}" CACHE PATH "Directory containing lv_conf.h for LVGL")
add_subdirectory("${LVGL_DIR}" lvgl_build)
#=============================================================================
# 包含路径
#=============================================================================
include_directories(
${CMAKE_CURRENT_SOURCE_DIR} # lv_conf.h (LVGL 找), dbg_log.h
${CMAKE_CURRENT_SOURCE_DIR}/sim # sim_port.h 等模拟器平台层
${LVGL_DIR} # lvgl.h
${LVGL_DIR}/src # lvgl 内部头文件
${UI_DIR} # ui_menu.h, ui_font_cn_12.h
${NET_DIR} # net_socket.h / net_types.h(net_* API 双端共享核心)
${NETCFG_DIR} # net_cfg.h(网络配置,双端共享核心)
${PROJECT_ROOT}/test/board # test_config.h / net_latency_test.h(共享核心
# ui_net_sink.c、net_socket.c 引含;探针默认关闭,
# 声明宿主安全;2026-09-21 修复模拟器构建断链;
# 2026-10-02 测试目录重构后头文件移入 test/board/)
${PROJECT_ROOT}/App/cfg # cfg_file.h / cfg_file_store.h(通用配置文件引擎,双端共享核心)
${PROJECT_ROOT}/App/protocol/iec104 # iec104_comm.h([comm] 段契约头,供 IEC104_SOURCES 编译;道G task-8)
${PROJECT_ROOT}/App/log # sys_log.h(运行/自检记录引擎,双端共享核心)
${PROJECT_ROOT}/App/algo # prot_set.h(定值模型纯算法,双端共享核心;见 ALGO_SOURCES)
${PROJECT_ROOT}/App/util # ioboard_di.h(开入去抖与快照,双端共享核心)
${PROJECT_ROOT}/Drivers/BSP # dbg_log.h(使用 simulator 的 dbg_cfg.h 配置)
${SDL2_DIR}/include # SDL2 头文件
)
#=============================================================================
# SDL2 库(使用本地预编译版本)
#=============================================================================
set(SDL2_INCLUDE_PARENT "${SDL2_DIR}/include")
set(SDL2_LIB_X64 "${SDL2_DIR}/lib/x64")
#=============================================================================
# 源文件
#=============================================================================
set(SIM_SOURCES
main.c
sim/sim_port.c
sim/sim_latency_stub.c # 探针符号宿主空实现(ui_net_sink.c 引用,见文件头注释)
)
# UI 源文件(与 MCU 端共用,直接编译)
set(UI_SOURCES
${UI_DIR}/ui_menu.c
${UI_DIR}/ui_menu_view.c
${UI_DIR}/ui_content_page.c
${UI_DIR}/ui_deco.c
${UI_DIR}/ui_page_device_info.c
${UI_DIR}/ui_page_ac.c
${UI_DIR}/ui_page_dc.c
${UI_DIR}/ui_page_password.c
${UI_DIR}/ui_page_net_cfg.c
${UI_DIR}/ui_page_runlog.c
${UI_DIR}/ui_page_selftest.c
${UI_DIR}/ui_standby.c
${UI_DIR}/ui_menu_tab.c
${UI_DIR}/ui_font_cn_12.c
${UI_DIR}/ui_net_sink.c
${UI_DIR}/ui_page_registry.c
${UI_DIR}/ui_style.c
${UI_DIR}/ui_w_records.c
${UI_DIR}/ui_w_editor.c
${UI_DIR}/ui_w_setlist.c
${UI_DIR}/ui_page_action.c
${UI_DIR}/ui_data.c # 数据快照存侧(道E task-14;写侧 App/app/ui_data_feed.c 不进模拟器,见 scripts/check_registration.py)
${UI_DIR}/ui_w_soe.c # SOE 记录组件(道E task-14;reader 已在批 2 两端绑定)
${UI_DIR}/ui_w_setview.c # 定值查看视图模型(道E task-15 批 3:四张视图表 + Q10 换算 + 越界反显)
${UI_DIR}/ui_w_ytview.c # 遥测整定视图模型(道F task-7:死区/系数两页共用注入表视图 + 落盘确认状态机)
${UI_DIR}/ui_page_soe.c
${UI_DIR}/ui_page_view_param.c
${UI_DIR}/ui_page_view_plate.c
${UI_DIR}/ui_page_view_set.c
${UI_DIR}/ui_page_view_word.c
${UI_DIR}/ui_page_yx.c
${UI_DIR}/ui_page_clear.c
${UI_DIR}/ui_page_clock.c
${UI_DIR}/ui_page_reset.c
${UI_DIR}/ui_page_calib.c
${UI_DIR}/ui_page_deadband.c
${UI_DIR}/ui_page_comm.c
${UI_DIR}/ui_page_accident.c
${UI_DIR}/ui_page_alarm.c
${UI_DIR}/ui_page_oper.c
${UI_DIR}/ui_page_runreport.c
${UI_DIR}/ui_page_start.c
${UI_DIR}/ui_page_yk.c
${UI_DIR}/ui_page_wave_manual.c
${UI_DIR}/ui_page_wave_play.c
${UI_DIR}/ui_page_sntp.c
)
# 运行/自检记录引擎(双端共享核心 + 平台存储后端;MCU 端编 sys_log_mcu.c,见 Keil 工程)
set(SYSLOG_SOURCES
sim/sim_syslog.c
)
# 网络配置(双端共享核心 + cfg_file 引擎 + 平台存储后端;MCU 端编 cfg_file_store_mcu.c,见 Keil 工程)
set(NETCFG_SOURCES
${NETCFG_DIR}/net_cfg.c
${NETCFG_DIR}/ftp_cfg.c
${NETCFG_DIR}/sntp_cfg.c
${PROJECT_ROOT}/App/cfg/cfg_file.c
sim/cfg_file_store_sim.c
)
# 保护定值模型(App/algo/prot_set.c 零平台依赖,双端共享核心)。
# 模拟器只需要"出厂默认定值"来发布 UI 快照帧(main.c 的 sim_publish_data_frames),
# 不在这里复制一份 40 项数字——抄表就等于造第二真相(同 scripts/check_font_charset.py
# "单一规则源"的同一治理口径)。
set(ALGO_SOURCES
${PROJECT_ROOT}/App/algo/prot_set.c
# 录波段格式与录波环(故障录波 P1/P2):两份都是零平台依赖纯逻辑——不 include HAL/CMSIS/RTOS、
# 不调 FatFs、不建 RTOS 对象、无 malloc。模拟器必须一起编译,因为「录波回放」页要在模拟器里
# 出真波形(峰值换算走 wave_store_code_to_milli,取数走 wave_ring_read_ch),数据由
# simulator/main.c 的合成节拍喂进 ring —— 与 prot_set.c 同一条「双端共享核心、不造第二真相」
# 口径,因此两份都**不进** scripts/check_registration.py 的 SIM_EXEMPT。
${PROJECT_ROOT}/App/algo/wave_store.c
${PROJECT_ROOT}/App/algo/wave_ring.c
)
# IEC 104 [comm] 配置段(道G task-8):模拟器运行期不跑 104 任务、无消费路径,
# 本 TU 仅为双端注册事实一致而编译(iec104 其余 .c 走 scripts 白名单逐个点名,
# 白名单是门禁地盘不在这里扩——新配对模块按 new-source-file 口径进显式源列表)。
set(IEC104_SOURCES
${PROJECT_ROOT}/App/protocol/iec104/iec104_comm.c
)
# 开入去抖与快照(App/util/ioboard_di.c):零平台依赖纯逻辑(只 include <stdint.h>),
# 主机侧单测覆盖于 test/host/ioboard。按 check_registration 的双端注册门禁,新 .c 必须
# 两端都编译(不像 MCU 硬件驱动那样进 SIM_EXEMPT),所以在这里显式列出。
set(IOBOARD_SOURCES
${PROJECT_ROOT}/App/util/ioboard_di.c
)
# 网络后端(net_* 核心 API 的 Winsock 实现 + UI 推流平台后端;MCU 端另编 net_socket.c 与 _mcu 后端)
set(NET_SOURCES
sim/net_socket_sim.c
sim/ui_net_sink_backend_sim.c
)
#=============================================================================
# 构建可执行文件
#=============================================================================
add_executable(lvgl_sim WIN32 ${SIM_SOURCES} ${UI_SOURCES} ${NETCFG_SOURCES} ${SYSLOG_SOURCES} ${NET_SOURCES} ${ALGO_SOURCES} ${IEC104_SOURCES} ${IOBOARD_SOURCES})
target_compile_definitions(lvgl_sim PRIVATE
LV_CONF_INCLUDE_SIMPLE # 让 lvgl.h 找到 lv_conf.h
LV_LVGL_H_INCLUDE_SIMPLE # ui_font_cn_12.c 内部 include 简化
WIN32_LEAN_AND_MEAN # 防止 Windows.h 拉入 winsock.h(与 winsock2.h 冲突)
NET_NO_OS # 剥离 net_socket.h 的 FreeRTOS 相关接口(纯 BSD Socket)
UI_REMO_ALLOW_GOTO # 模拟器构建启用 GOTO(5) 直开页(#69,2026-11-02;台架 MCU 门控 DTU_BENCH,见 ui_net_sink.c 注释)
)
target_include_directories(lvgl_sim PRIVATE
${SDL2_INCLUDE_PARENT} # SDL2/SDL.h 路径
)
target_link_directories(lvgl_sim PRIVATE
${SDL2_LIB_X64}
)
target_link_libraries(lvgl_sim
lvgl
SDL2
SDL2main
ws2_32
)
# 数学库(非 MSVC)
if(NOT MSVC)
target_link_libraries(lvgl_sim m pthread)
endif()
# Windows 子系统:控制台(显示 printf 输出)
if(WIN32)
if(MSVC)
target_link_options(lvgl_sim PRIVATE "/SUBSYSTEM:CONSOLE")
else()
target_link_options(lvgl_sim PRIVATE "-mconsole")
endif()
endif()
# 复制 SDL2.dll 到输出目录
add_custom_command(TARGET lvgl_sim POST_BUILD
COMMAND ${CMAKE_COMMAND} -E copy_if_different
"${SDL2_LIB_X64}/SDL2.dll"
"$<TARGET_FILE_DIR:lvgl_sim>/SDL2.dll"
COMMENT "Copying SDL2.dll to output directory"
)
#=============================================================================
# 自定义目标:运行模拟器
#=============================================================================
add_custom_target(run COMMAND ${CMAKE_BINARY_DIR}/lvgl_sim DEPENDS lvgl_sim)
#=============================================================================
# 调试模式额外警告
#=============================================================================
if(CMAKE_BUILD_TYPE STREQUAL "Debug")
message(STATUS "Debug mode enabled for simulator")
if(MSVC)
target_compile_options(lvgl_sim PRIVATE /W4)
else()
target_compile_options(lvgl_sim PRIVATE -Wall -Wextra -Wpedantic)
endif()
endif()
message(STATUS "=== LVGL Simulator ===")
message(STATUS "Screen: 160x160, 1bpp monochrome")
message(STATUS "LVGL dir: ${LVGL_DIR}")
message(STATUS "UI dir: ${UI_DIR}")
message(STATUS "SDL2: ${SDL2_DIR}")