STM32F4-Base/test/host/iec104_serv/iec104_serv_test.c

/*
 * 模块名称：IEC 60870-5-104 上行服务生命周期（iec104_serv）主机侧单元测试
 * 模块功能：在 PC 上离线验证 App/task/iec104_serv.c 的服务侧骨架：监听建立与失败
 *           回收、**网络代次一变就重建监听**（改了 IP 端口必须在新地址上继续服务）、
 *           accept 门控与表项失效自愈、单连接 socket 的断线语义（对端 FIN 只关数据
 *           口、绝不关监听）、连续短写判死、活性分频探活、协议状态掉回 IDLE 时丢
 *           连接并立即重建，以及时钟桥接的两个溢出边界（>4G 秒拒绝、未对时返回哨兵
 *           而不是把 1970 当真实时间）。
 *
 * 被测对象：真实源文件 ../../../App/task/iec104_serv.c（#include 纳入，故它的 static
 *           s_bind_listen / s_drop_conn / s_service_link / s_serv_poll / s_send_apdu /
 *           s_clock_sync / s_epoch_ms 都能直接驱动——**不跑 iec104_serv_task 的无限
 *           主循环**，那是 never-returning 的任务体，不适合单测）。
 *           iec104_link.h / iec104_pts.h / prot_set.h / sys_clock.h / sys_events.h /
 *           task_watchdog.h / net_types.h 全用**真实头**（iec104_state_t 枚举、
 *           iec104_link_cfg_t 函数指针签名、TASK_WD_IEC104=7、SYS_EVT_* 位值一改即
 *           编译期报错）；链路层（iec104_link_*）与 pts 层给假件——链路协议本身有
 *           test/host/iec104 的 97 条专测，本模块只管"服务怎么活、怎么死、怎么重生"。
 *
 * 为什么要主机侧单测（而不是只靠台架）：
 *   1. 104 主站掉线重连是**现场最常见的故障形态**，但台架上没法按需制造"改 IP 时
 *      正好有连接""对端 FIN 与 RST 的区别""连续三次短写"这些时序；而这里每一条
 *      处理错的后果都是端口永久失联或会话卡死，只能靠主站侧超时才发现。
 *   2. 判死用**连续**短写计数（一次成功即复位），写成"累计"就会把偶发拥塞误判成
 *      断线，主站看到的就是莫名掉线——这条只有能精确注入短写/成功序列才可测。
 *   3. 时钟桥接的两个边界：epoch 秒超过 32 位必须拒绝（否则截断成 2106 年前的某个
 *      乱值写进 RTC），未对时（sys_clock_get 返回 UINT32_MAX）必须回哨兵而不是 0，
 *      否则对端会以为设备时间是 1970-01-01。
 *   4. 活性分频（每 32 轮才探一次）是 CPU 预算的取舍：写错成每轮都探，就把 100ms
 *      轮询变成了每轮两次系统调用；写错成分频相位，TESTFR 会迟迟不发。
 *   5. 操作记录是**审计面**（道F task-19）：只要"投了"而不管"改成功了没有"，屏上的
 *      操作记录页就会出现从没发生过的对时；越界拒绝与 RTC 写失败这两条腿必须
 *      一条都不投，而这只有能注入 sys_clock_set_unix 的返回值才测得到。
 *      同时钉住"用 quiet 口不用 post 口"——post 的两个满态留痕分支各带约 216 B
 *      内联行缓冲，iec104Task 的静态最坏链放不下它（台架与单测都看不出这个差别，
 *      只有 stack_report 会响，所以先在源码侧钉住）。
 *
 * 覆盖点：TC-I104SRV-001..004 建监听（001b/c = 端口与公共地址取自 [comm] 段
 *   getter，道G task-8 取值来源改造）；010..013 发送与连续短写判死；020..023 时钟
 *   桥接；030..033 代次重建与 accept 门控；034..036 活性分频与对端 FIN；037..041
 *   错误丢弃与协议掉线重生；050..053 对时的操作记录（道F task-19：成功才记、
 *   越界拒绝与写钟失败两条腿都不记、每次对时各记一条、且只走 quiet 投递口）。
 *
 * 通过：全部 TC PASS（main 返回 0）。
 * 入口：int main(void)，返回 0=PASS / 1=FAIL（由 run 脚本判读）。
 *
 * 创建日期：2026-10-23
 */

#include <stdio.h>
#include <string.h>

#include "iec104_serv.h"
#include "net_socket.h"

#include "iec104_serv.c"

static int s_total;
static int s_passed;
static int s_failed;

#define CHECK(cond, name) do { \
    s_total++; \
    if (cond) { s_passed++; printf("  PASS %s\n", name); } \
    else { s_failed++; printf("  FAIL %s (line %d)\n", name, __LINE__); } \
} while (0)

int g_i4_info_count;
int g_i4_error_count;
int g_i4_debug_count;

/* 真实 sys_events.h 把它声明成 extern，这里给定义（本模块只在主循环里用，
   测试设成 NULL 走"事件组不可用"支路，不阻塞静态辅助函数的驱动）。 */
osEventFlagsId_t sys_evtHandle;

/* ===================== 可控 socket 面 ===================== */

typedef struct {
    int      socket_rc;
    int      bind_rc;
    int      listen_rc;
    int      accept_rc;
    int      send_rc;
    int      recv_rc;
    int      can_read;
    int      armed;
    int      errno_val;
    uint32_t gen;
    int      sock_exists;
    int      socket_calls;
    int      bind_calls;
    int      listen_calls;
    int      accept_calls;
    int      close_calls;
    int      last_closed_fd;
    int      last_accept_sock;
    int      recv_calls;
    uint16_t last_bind_port_net;
    uint16_t last_bind_family;
    uint32_t last_bind_addr;
    int      delay_calls;
} i4_net_t;

static i4_net_t g_n;

/* net_get_sock 要返回一个真 net_sock_t（结构来自真实 net_types.h），先声明再用 */
static net_sock_t g_sock_probe;

int net_socket(int domain, int type) { (void)domain; (void)type; g_n.socket_calls++; return g_n.socket_rc; }
int net_bind(int sockfd, const struct net_sockaddr *addr, int addrlen)
{
    const struct net_sockaddr_in *a = (const struct net_sockaddr_in *)addr;

    (void)sockfd;
    (void)addrlen;
    g_n.bind_calls++;
    g_n.last_bind_port_net = a->sin_port;
    g_n.last_bind_family = a->sin_family;
    g_n.last_bind_addr = a->sin_addr.s_addr;
    return g_n.bind_rc;
}
int net_listen(int sockfd) { (void)sockfd; g_n.listen_calls++; return g_n.listen_rc; }
int net_accept(int sockfd, struct net_sockaddr *addr, int *addrlen)
{
    (void)addr;
    (void)addrlen;
    g_n.accept_calls++;
    g_n.last_accept_sock = sockfd;
    return g_n.accept_rc;
}
int net_close(int sockfd) { g_n.close_calls++; g_n.last_closed_fd = sockfd; return 0; }
int net_send(int sockfd, const void *buf, int len, int flags)
{
    (void)sockfd;
    (void)buf;
    (void)flags;
    return g_n.send_rc;
}
int net_recv_nb(int sockfd, void *buf, int len)
{
    (void)sockfd;
    (void)buf;
    (void)len;
    g_n.recv_calls++;
    return g_n.recv_rc;
}
int net_can_read(int sockfd) { (void)sockfd; return g_n.can_read; }
int net_get_errno(void) { return g_n.errno_val; }
int net_listener_armed(int sockfd) { (void)sockfd; return g_n.armed; }
uint32_t net_get_generation(void) { return g_n.gen; }
net_sock_t *net_get_sock(int sockfd) { (void)sockfd; return (g_n.sock_exists != 0) ? &g_sock_probe : NULL; }
uint16_t net_htons(uint16_t v) { return (uint16_t)((v >> 8) | (v << 8)); }

/* ===================== 假链路层与假 pts ===================== */

static int      g_lk_init;
static uint16_t g_lk_init_ca;   /* [comm] ca 透传钉（道G task-8）：init 收到的 cfg->ca */
static int      g_lk_open;
static int      g_lk_close;
static int      g_lk_poll;
static int      g_lk_onrx;
static uint32_t g_lk_last_now;
static iec104_state_t g_lk_state;

void iec104_link_init(iec104_link_t *lk, const iec104_link_cfg_t *cfg, void *ctx)
{
    (void)lk; (void)ctx;
    g_lk_init_ca = cfg->ca;             /* 道G task-8：钉 ca 真的进了链路 */
    g_lk_init++;
}
void iec104_link_open(iec104_link_t *lk, uint32_t now_ms)
{
    (void)lk;
    g_lk_open++;
    g_lk_last_now = now_ms;
}
void iec104_link_close(iec104_link_t *lk) { (void)lk; g_lk_close++; }
void iec104_link_poll(iec104_link_t *lk, uint32_t now_ms)
{
    (void)lk;
    g_lk_poll++;
    g_lk_last_now = now_ms;
}
void iec104_link_on_rx(iec104_link_t *lk, const uint8_t *data, uint16_t len, uint32_t now_ms)
{
    (void)lk; (void)data; (void)len; (void)now_ms;
    g_lk_onrx++;
}
iec104_state_t iec104_link_state(const iec104_link_t *lk) { (void)lk; return g_lk_state; }

static int g_pts_init;
void iec104_pts_init(void) { g_pts_init++; }

/* ===================== [comm] getter 桩（道G task-8） =====================
 * 真 getter（合法带自愈）在 iec104_comm.c，由 test/host/iec104 真链套
 * TC-IEC104-031~033 覆盖；本套只钉 serv 的**取值来源**：端口每次 bind 现取、
 * ca 任务启动取一次。 */
static uint16_t g_comm_ca   = IEC104_COMM_DEF_CA;
static uint16_t g_comm_port = IEC104_COMM_DEF_PORT;
uint16_t iec104_comm_ca(void) { return g_comm_ca; }
uint16_t iec104_comm_port(void) { return g_comm_port; }

/* ===================== 假时钟 / 定值 / 看门狗 / RTOS ===================== */

static uint32_t g_clock_val;
static int      g_clock_set_rc;
static uint32_t g_clock_last_secs;
static int      g_clock_set_calls;
static uint32_t g_dirty;
static int      g_evt_set_calls;
static uint32_t g_evt_last;
static int      g_wd_beats;
static int      g_wd_last_id;
static uint32_t g_now;

/* ===================== sys_log 桩（task-19 操作记录） =====================
 * 两个投递口都抓下来：quiet 是 iec104Task 该用的那个（本任务栈深，不许在调用链上
 * 内联日志行缓冲），post 一旦在这里被调到就是"绕回旧口"，053 会红。
 * 投递本身（收/丢/计数）归 test/host/sys_log_mcu，本套只钉"哪条腿投了哪一句"。 */
#include "sys_log.h"

#define RP_I4_REC_MAX 8u
static uint8_t  rp_i4_id[RP_I4_REC_MAX];
static char     rp_i4_desc[RP_I4_REC_MAX][SYSLOG_DESC_MAX + 1u];
static uint32_t rp_i4_n;              /* quiet 通道累计（不回绕，供"恰好几条"断言） */
static uint32_t rp_i4_post_n;         /* 误用 syslog_post 的次数，期望恒 0 */

static void rp_i4_rec_clear(void)
{
    rp_i4_n = 0u;
    rp_i4_post_n = 0u;
    (void)memset(rp_i4_id, 0, sizeof(rp_i4_id));
    (void)memset(rp_i4_desc, 0, sizeof(rp_i4_desc));
}

void syslog_post_quiet(syslog_id_t id, const char *desc)
{
    uint32_t slot = rp_i4_n % RP_I4_REC_MAX;
    size_t   dl = 0u;

    if (desc == NULL) {
        return;
    }
    while ((dl < SYSLOG_DESC_MAX) && (desc[dl] != '\0')) {
        dl++;
    }
    (void)memcpy(rp_i4_desc[slot], desc, dl);
    rp_i4_desc[slot][dl] = '\0';
    rp_i4_id[slot] = (uint8_t)id;
    rp_i4_n++;
}

void syslog_post(syslog_id_t id, const char *desc)
{
    (void)id;
    (void)desc;
    rp_i4_post_n++;
}

uint32_t syslog_post_dropped(void) { return 0u; }

static int rp_i4_at(uint32_t k, syslog_id_t id, const char *desc)
{
    if (k >= rp_i4_n) {
        return 0;
    }
    return (rp_i4_id[k % RP_I4_REC_MAX] == (uint8_t)id)
           && (strcmp(rp_i4_desc[k % RP_I4_REC_MAX], desc) == 0) ? 1 : 0;
}

uint32_t sys_clock_get(void) { return g_clock_val; }
int sys_clock_set_unix(uint32_t unix_secs)
{
    g_clock_set_calls++;
    g_clock_last_secs = unix_secs;
    return g_clock_set_rc;
}
uint8_t prot_set_dirty_peek(void) { return (uint8_t)g_dirty; }
/* run_par 脏 peek 假件（卡 10）：任务主循环在单测中不跑，脏恒 0 =
 * 不投递 SYS_EVT_RUN_PAR_SAVE；落盘链真身覆盖在 test/host/run_par。 */
uint8_t run_par_dirty_peek(void) { return 0u; }
uint32_t osEventFlagsSet(osEventFlagsId_t ef_id, uint32_t flags)
{
    (void)ef_id;
    g_evt_set_calls++;
    g_evt_last = flags;
    return flags;
}
uint32_t osEventFlagsWait(osEventFlagsId_t ef_id, uint32_t flags, uint32_t options, uint32_t timeout)
{
    (void)ef_id; (void)flags; (void)options; (void)timeout;
    return 0u;
}
void task_wd_beat(task_wd_id_t id) { g_wd_beats++; g_wd_last_id = (int)id; }
uint32_t osKernelGetTickCount(void) { return g_now; }
void osDelay(uint32_t ticks)
{
    (void)ticks;
    g_n.delay_calls++;
    if (g_n.delay_calls > 500) {
        printf("  ABORT runaway (>500 osDelay rounds)\n");
        fflush(stdout);
        exit(2);
    }
}

/* ===================== 复位 ===================== */

static void reset_all(void)
{
    (void)memset(&g_n, 0, sizeof(g_n));
    g_n.socket_rc = 5;
    g_n.bind_rc = 0;
    g_n.listen_rc = 0;
    g_n.accept_rc = -1;
    g_n.send_rc = 0;
    g_n.armed = 1;
    g_n.sock_exists = 1;
    g_n.errno_val = NET_ERR_WOULDBLOCK;
    g_n.gen = 100u;
    (void)memset(&g_sock_probe, 0, sizeof(g_sock_probe));
    g_lk_init = 0; g_lk_open = 0; g_lk_close = 0; g_lk_poll = 0; g_lk_onrx = 0;
    g_lk_last_now = 0u;
    g_lk_state = IEC104_ST_RUN;
    g_lk_init_ca = 0u;
    g_pts_init = 0;
    g_comm_ca = IEC104_COMM_DEF_CA;
    g_comm_port = IEC104_COMM_DEF_PORT;
    s_cfg.ca = IEC104_COMM_DEF_CA;
    g_clock_val = 1700000000u;
    rp_i4_rec_clear();
    g_clock_set_rc = 0;
    g_clock_last_secs = 0u;
    g_clock_set_calls = 0;
    g_dirty = 0u;
    g_evt_set_calls = 0;
    g_evt_last = 0u;
    g_wd_beats = 0;
    g_wd_last_id = -1;
    g_now = 5000u;
    g_i4_info_count = 0;
    g_i4_error_count = 0;
    g_i4_debug_count = 0;
    sys_evtHandle = NULL;
    s_listen = -1;
    s_client = -1;
    s_gen = 100u;
    s_liveness_ctr = 0u;
    s_send_fail_run = 0u;
    s_conn_dead = 0u;
}

/* ===================== 建监听 ===================== */

static void tc_bind_listen(void)
{
    printf("-- TC-I104SRV-001..004 bind/listen --\n");
    reset_all();
    CHECK((s_bind_listen() == 0) && (s_listen == 5) && (g_n.listen_calls == 1) &&
          (g_n.last_bind_family == NET_AF_INET) &&
          (g_n.last_bind_port_net == net_htons(IEC104_COMM_DEF_PORT)) &&
          (g_n.last_bind_addr == NET_INADDR_ANY),
          "TC-I104SRV-001 build the listener: [comm] default port through htons, bind to any address, remember the listen handle");

    reset_all();
    g_comm_port = 9002u;               /* [comm] 可配值：非标准端口（道G task-8） */
    CHECK((s_bind_listen() == 0) && (g_n.last_bind_port_net == net_htons(9002u)),
          "TC-I104SRV-001b bind takes the [comm] getter value, not the compile-time 2404");

    reset_all();
    g_comm_ca = 7u;
    s_apply_comm_ca();                 /* 任务启动链路同款动作（ca = 重启生效） */
    iec104_link_init(&s_link, &s_cfg, NULL);
    CHECK((s_cfg.ca == 7u) && (g_lk_init_ca == 7u) && (g_lk_init == 1),
          "TC-I104SRV-001c task-start ca fill reaches the link cfg ([comm] value source)");
    g_comm_ca = 9u;
    s_apply_comm_ca();
    CHECK(s_cfg.ca == 9u, "TC-I104SRV-001c every task start re-reads the section (restart semantics)");

    reset_all();
    g_n.socket_rc = -1;
    CHECK((s_bind_listen() == -1) && (g_n.bind_calls == 0) && (g_n.close_calls == 0),
          "TC-I104SRV-002 if no socket can be created return at once: no bind and no close of a handle that does not exist");

    reset_all();
    g_n.bind_rc = -1;
    CHECK((s_bind_listen() == -1) && (g_n.close_calls == 1) && (g_n.listen_calls == 0),
          "TC-I104SRV-003 a bind failure must close the socket just created (otherwise every retry leaks a handle)");

    reset_all();
    g_n.listen_rc = -1;
    CHECK((s_bind_listen() == -1) && (g_n.close_calls == 1) && (s_listen == -1),
          "TC-I104SRV-004 a listen failure also closes it and leaves no half-built listener");
}

/* ===================== 发送与连续短写判死 ===================== */

static void tc_send(void)
{
    const uint8_t apdu[4] = { 0x68u, 0x02u, 0x00u, 0x00u };

    printf("-- TC-I104SRV-010..013 send & fail streak --\n");
    reset_all();
    s_client = -1;
    s_send_apdu(NULL, apdu, 4u);
    CHECK((g_n.send_rc == 0) && (g_n.close_calls == 0) && (g_i4_error_count == 0),
          "TC-I104SRV-010 with no connection it returns directly (no net_send, no error)");

    reset_all();
    s_client = 7;
    g_n.send_rc = 4;
    s_send_apdu(NULL, apdu, 4u);
    CHECK((s_send_fail_run == 0u) && (s_conn_dead == 0u),
          "TC-I104SRV-011 a fully sent frame clears the consecutive-failure counter");

    reset_all();
    s_client = 7;
    g_n.send_rc = 2;                       /* 短写：只发了 2/4 */
    s_send_apdu(NULL, apdu, 4u);
    CHECK((s_send_fail_run == 1u) && (s_conn_dead == 0u) && (g_i4_error_count == 1),
          "TC-I104SRV-012 the first short write is logged but does not declare death (congestion is normal)");
    s_send_apdu(NULL, apdu, 4u);
    s_send_apdu(NULL, apdu, 4u);
    CHECK((s_send_fail_run == 3u) && (s_conn_dead == 1u),
          "TC-I104SRV-012b only the 3rd failure in a row declares death (IEC104_SEND_FAIL_MAX)");

    reset_all();
    s_client = 7;
    g_n.send_rc = 1;
    s_send_apdu(NULL, apdu, 4u);
    s_send_apdu(NULL, apdu, 4u);
    g_n.send_rc = 4;
    s_send_apdu(NULL, apdu, 4u);            /* 中间成功一次 */
    g_n.send_rc = 1;
    s_send_apdu(NULL, apdu, 4u);
    s_send_apdu(NULL, apdu, 4u);
    CHECK((s_conn_dead == 0u) && (s_send_fail_run == 2u),
          "TC-I104SRV-013 success resets the counter: occasional congestion never adds up into a false kill");
}

/* ===================== 时钟桥接边界 ===================== */

static void tc_clock(void)
{
    printf("-- TC-I104SRV-020..023 clock bridge --\n");
    reset_all();
    CHECK(s_clock_sync(NULL, 0x100000000ULL * 1000ULL) == -1,
          "TC-I104SRV-020 any second count beyond 32 bits is rejected (truncating it into the RTC means garbage past 2106)");
    CHECK(g_clock_set_calls == 0, "TC-I104SRV-020b when rejected the clock must not be touched at all");

    reset_all();
    (void)s_clock_sync(NULL, 1700000123000ULL);
    CHECK((g_clock_set_calls == 1) && (g_clock_last_secs == 1700000123u),
          "TC-I104SRV-021 milliseconds become seconds by integer division before the clock is written");

    reset_all();
    g_clock_val = UINT32_MAX;               /* 未对时的哨兵值 */
    CHECK(s_epoch_ms(NULL) == UINT64_MAX,
          "TC-I104SRV-022 without time sync return the UINT64_MAX sentinel (1970 must never pass for device time)");

    reset_all();
    g_clock_val = 1700000123u;
    CHECK(s_epoch_ms(NULL) == 1700000123000ULL, "TC-I104SRV-023 with a synced clock the answer is in milliseconds");

    /* ---- task-19：对时 = 操作记录（审计面只记真发生过的动作） ---- */
    reset_all();
    (void)s_clock_sync(NULL, 1700000123000ULL);
    CHECK((rp_i4_n == 1u) && (rp_i4_at(0u, SYSLOG_OPER, "clock set by 104") == 1),
          "TC-I104SRV-050 a successful sync books exactly one operation record naming the source");

    reset_all();
    (void)s_clock_sync(NULL, 0x100000000ULL * 1000ULL);
    CHECK((rp_i4_n == 0u) && (g_clock_set_calls == 0),
          "TC-I104SRV-050b the out-of-range rejection books nothing (an audit record for something that never happened is worse than none)");

    reset_all();
    g_clock_set_rc = -1;                  /* 写钟失败（RTC 回写失败那一类） */
    CHECK(s_clock_sync(NULL, 1700000123000ULL) == -1,
          "TC-I104SRV-051 a failed clock write still answers the link layer with -1");
    CHECK(rp_i4_n == 0u,
          "TC-I104SRV-051b a failed clock write books no operation record");

    reset_all();
    (void)s_clock_sync(NULL, 1700000123000ULL);
    (void)s_clock_sync(NULL, 1700000456000ULL);
    CHECK((rp_i4_n == 2u) && (rp_i4_at(1u, SYSLOG_OPER, "clock set by 104") == 1),
          "TC-I104SRV-052 every re-sync is its own operation record (no dedup, no latching)");

    /* 053：用错投递口的形状——iec104Task 是深链任务，只许用 quiet。
     *      顺带量文案长度：超过 SYSLOG_DESC_MAX 会在投递侧被静默截断。 */
    reset_all();
    (void)s_clock_sync(NULL, 1700000123000ULL);
    CHECK((rp_i4_post_n == 0u) && (rp_i4_n == 1u)
          && (strlen("clock set by 104") <= SYSLOG_DESC_MAX),
          "TC-I104SRV-053 the record goes out over the stack-safe channel only, and its text fits the record field");
}

/* ===================== 代次重建与 accept 门控 ===================== */

static void tc_generation(void)
{
    printf("-- TC-I104SRV-030..033 generation & accept gate --\n");
    reset_all();
    s_listen = 5;
    s_client = 9;
    g_n.gen = 101u;                         /* 网络重建（现场改了 IP） */
    s_serv_poll();
    CHECK((g_n.close_calls == 2) && (g_n.last_closed_fd == 5) &&
          (s_client == -1) && (s_liveness_ctr == 0u) && (s_conn_dead == 0u) &&
          (g_lk_close == 1) && (s_gen == 101u) && (g_n.bind_calls == 1),
          "TC-I104SRV-030 a generation change tears down the old connection and listener and rebuilds them (the port must keep serving on the new IP)");

    reset_all();
    s_listen = -1;
    s_serv_poll();
    CHECK((g_n.bind_calls == 1) && (s_listen == 5) && (g_n.accept_calls == 0),
          "TC-I104SRV-031 a lost listener is rebuilt and this round does not accept");

    reset_all();
    s_listen = 5;
    g_n.armed = 0;                          /* 监听还没就绪 */
    g_n.sock_exists = 1;
    s_serv_poll();
    CHECK((g_n.accept_calls == 0) && (s_listen == 5),
          "TC-I104SRV-032 no accept while the listener gate is down (otherwise it spins on a handle that is not ready)");

    reset_all();
    s_listen = 5;
    g_n.armed = 0;
    g_n.sock_exists = 0;                    /* 表项已不存在 */
    s_serv_poll();
    CHECK((s_listen == -1) && (g_n.accept_calls == 0),
          "TC-I104SRV-032b once the slot is invalid the listen handle is dropped and rebuilt next round");

    reset_all();
    s_listen = 5;
    g_n.accept_rc = 9;
    s_send_fail_run = 3u;
    s_conn_dead = 1u;
    s_liveness_ctr = 7u;
    s_serv_poll();
    CHECK((s_client == 9) && (g_lk_open == 1) && (g_lk_last_now == 5000u) &&
          (s_send_fail_run == 0u) && (s_conn_dead == 0u) && (s_liveness_ctr == 0u) &&
          (g_i4_info_count == 1),
          "TC-I104SRV-033 a new connection opens the link and resets all three failure counters");
}

/* ===================== 活性分频、对端 FIN、错误丢弃 ===================== */

static void tc_liveness(void)
{
    printf("-- TC-I104SRV-034..041 liveness / EOF / drop --\n");
    reset_all();
    s_listen = 5;
    s_client = 9;
    g_n.can_read = 0;
    s_liveness_ctr = 0u;
    s_serv_poll();
    CHECK((g_n.recv_calls == 0) && (g_lk_poll == 1) && (s_liveness_ctr == 1u),
          "TC-I104SRV-034 with nothing readable the liveness probe runs on a divide-by-32 tick and this round receives nothing (saves CPU budget)");

    reset_all();
    s_listen = 5;
    s_client = 9;
    g_n.can_read = 0;
    /* 这一轮收到的是"暂无数据"（非阻塞的空读），而不是 0——0 在 recv_nb 的语义里是
     * 对端 FIN，会直接走 036 那条断开支路，测不到分频本身。 */
    g_n.recv_rc = -1;
    g_n.errno_val = NET_ERR_WOULDBLOCK;
    s_liveness_ctr = 31u;                   /* 下一轮正好到分频点 */
    s_serv_poll();
    CHECK((g_n.recv_calls == 1) && (g_lk_poll == 1) && (s_client == 9),
          "TC-I104SRV-035 only when the divider fires does it receive once (liveness frames such as TESTFR depend on it going out)");

    reset_all();
    s_listen = 5;
    s_client = 9;
    g_n.can_read = 1;
    g_n.recv_rc = 0;                        /* 对端 FIN */
    s_serv_poll();
    CHECK((g_n.last_closed_fd == 9) && (s_client == -1) && (g_lk_close == 1) &&
          (g_n.close_calls == 1) && (s_listen == 5) && (g_n.bind_calls == 0),
          "TC-I104SRV-036 a normal peer disconnect closes only the data socket: the listener must stay (on a single-socket chip closing the wrong one kills the port)");

    reset_all();
    s_listen = 5;
    s_client = 5;                           /* 单连接复用：数据号 == 监听号 */
    g_n.can_read = 1;
    g_n.recv_rc = 0;
    s_serv_poll();
    CHECK((g_n.close_calls == 0) && (s_client == -1) && (g_lk_close == 1),
          "TC-I104SRV-036b when the data handle equals the listen handle it must NOT be closed (that would destroy the listener too)");

    reset_all();
    s_listen = 5;
    s_client = 9;
    g_n.can_read = 1;
    g_n.recv_rc = -1;
    g_n.errno_val = NET_ERR_WOULDBLOCK;     /* 空转：没数据可读 */
    s_serv_poll();
    CHECK((s_client == 9) && (g_lk_close == 0) && (g_i4_error_count == 0),
          "TC-I104SRV-037 WOULDBLOCK is normal idling and must not drop the connection as an error");

    reset_all();
    s_listen = 5;
    s_client = 9;
    g_n.can_read = 1;
    g_n.recv_rc = -1;
    g_n.errno_val = NET_ERR_CONNRESET;      /* 真错误 */
    s_serv_poll();
    CHECK((s_client == -1) && (s_listen == 5) && (g_i4_error_count == 1) &&
          (g_lk_close == 1) && (s_liveness_ctr == 0u),
          "TC-I104SRV-038 a real error drops the connection and rebuilds the listener on the spot (no gap in service)");

    reset_all();
    s_listen = 5;
    s_client = 9;
    s_conn_dead = 1u;
    s_service_link(1000u);
    CHECK((s_client == -1) && (g_n.close_calls == 1) && (g_i4_error_count == 1),
          "TC-I104SRV-039 after death is declared service_link does the teardown (the send-failure path is a separate case)");

    reset_all();
    s_listen = 5;
    s_client = 9;
    g_lk_state = IEC104_ST_IDLE;            /* 链路层自己回到了未建立 */
    s_service_link(1000u);
    CHECK((s_client == -1) && (g_lk_close >= 1) && (s_listen == 5),
          "TC-I104SRV-040 falling back to IDLE also drops and respawns the session (otherwise the service stays up but never serves)");

    reset_all();
    s_listen = 9;
    s_client = 9;
    g_n.socket_rc = -1;                     /* 重建失败 */
    g_n.sock_exists = 0;                    /* 且表项已经没了 */
    g_n.can_read = 1;
    g_n.recv_rc = 0;
    s_serv_poll();
    CHECK((s_client == -1) && (s_listen == -1) && (g_n.close_calls == 0),
          "TC-I104SRV-041 slot gone and the rebuild failed: drop the stale listen handle and retry next round (never close it while it equals the data handle)");
}

int main(void)
{
    printf("=== IEC104 SERV Tests ===\n");

    tc_bind_listen();
    tc_send();
    tc_clock();
    tc_generation();
    tc_liveness();

    printf("\n=== IEC104 SERV Tests: %d/%d PASSED (failed=%d) ===\n",
           s_passed, s_total, s_failed);
    return (s_failed == 0) ? 0 : 1;
}