Files
STM32F4-Base/test
wandering1 74efa671bb feat(ioboard): wire 6 new CubeMX pins into 10-channel DO driver
Flat-expand the board output driver from 4 to 10 channels as decided:
IOBOARD_DO_COUNT 4->10, mask uint8_t->uint16_t, IOBOARD_DO_MASK_ALL
0x03FF.  The 6 new pins keep their bit positions: KO_LED1=PF2(bit4),
KO_LED2=PF3(bit5), KO_24V=PF4(bit6), KO4=PF5(bit7), KO5=PC15(bit8),
KO_LED3=PE6(bit9); the original 4 (KO6/TRIP/ERT/CLZ) keep bit0..3.
Backups-domain PC15 is used as a signal bit only (+/-3 mA limit).

No 24V supply interlock and no LED special-casing: the driver writes
KO_24V as an ordinary bit; callers needing relay power sequencing must
assert it before energizing a channel.  do_write/get/read_level and the
shadow register are all uint16_t; do_apply flushes four port segments
(GPIOC/GPIOF/GPIOC/GPIOE) and do_read_level caches three port ODRs.

UI: UI_DATA_DO_N 4->10, dio_do_mask uint16_t, UI_DATA_VER 3->4 because
dio_do_valid shifts 211->212; feed mask and dio row table extended;
content-page golden references regenerated for 51 rows / 7 pages.
Host ioboard tests 127/127 and ui_data tests 305/305 pass; Keil rebuild
0 errors 0 warnings.  RAM ledger, memory snapshot and size attestation
refilled from the authoritative map.  Docs: ioboard spec v1.2->v1.3 and
the resolved 6-pin question closed out.
2026-11-18 14:25:32 +08:00
..

test/ — 测试代码与主机端脚本

测试分两部分,物理隔离在两个子目录:

  • board/ —— 板端测试套件(.c/.h,编入固件由 testTask 执行)
  • host/ —— 主机端脚本(.py,PC 侧驱动板子并判读结果)

目录结构

目录 内容 README
board/ 板端测试套件(编入 Keil 工程,占 RAM) board/README.md
host/ PC 端测试/判读脚本(Python) host/README.md
run_all_suites.py 多套件回归编排(改宏 → 构建 → 烧录 → 采集,try/finally 保证还原开关);--check-build = 只编译不烧录(纯离机) 本文 §多套件回归

运行方式

# /serial-boot-test 一键闭环(推荐)
& '.venv\Scripts\python.exe' .dsh/skills/serial-boot-test/scripts/run_boot_test.py

# 单独校验日志
& '.venv\Scripts\python.exe' .dsh/skills/serial-boot-test/scripts/verify_log.py <日志文件>

# 多套件回归编排(需真机;自动改开关 + 构建 + 烧录 + 采集,结束后还原)
& '.venv\Scripts\python.exe' test/run_all_suites.py
& '.venv\Scripts\python.exe' test/run_all_suites.py --suites STORAGE,GD5F
& '.venv\Scripts\python.exe' test/run_all_suites.py --dry-run      # 只看计划

# 只编译不烧录(不需要 MCU / 串口 / ST-LINK,验证 4 套件可编译性)
& '.venv\Scripts\python.exe' test/run_all_suites.py --check-build

退出码约定:0=PASS / 1=FAIL / 2=采集或烧录错误 / 3=用法或预检错误。

多套件回归(run_all_suites.py)

套件互斥(编译期 #error)意味着跑 4 个套件要手工循环 4 轮。本脚本把它编排成一条 命令,并且无条件还原 test_config.h——跑完忘还原 = 测试固件进库,这是它存在的 核心理由(与提交期门禁 test-suite-switch 互为独立防线)。

⚠️ 每轮要真机烧录 + 采集,4 套件约数分钟起;破坏性套件还会改设备持久状态。 仅回归窗口用,绝不挂 pre-commit。

--check-build 则相反:只改宏 + /keil-build,不烧录不采集,无需任何硬件,用于防止 "测试套件长期编不过而无人知"(2026-08~09 CH395F 套件实例)。改动 test/board/ 下测试 代码后建议先跑它——实测 4 套件均 BUILD_OK: 0 errors, 0 warnings。

⚠️ 注意

  • 本目录被 pre-commit 门禁排除(测试代码不受 C 规范约束)
  • board/ 套件占用 RAM,启用前先核算预算(见 docs/内存管理/)
  • Keil 工程已同步:board/ 下 7 个 .c 编入 MDK-ARM/STM32F4-Demo.uvprojx, IncludePath 含 ../test/board;移动文件须同步改工程文件
  • 套件选择开关:board/test_config.h 的 TEST_SUITE_*(互斥,一次只启用一个)
  • 测试缓冲用分 Phase 复用静态缓冲(避免 L6406E 溢出)

相关文档

  • docs/测试说明/流程与规范/测试开发标准流程.md — 测试验证分层与门禁决策表
  • docs/测试说明/流程与规范/自动化测试流程.md — /serial-boot-test 细节与失败模式
  • 各模块测试指南:docs/测试说明/板级测试/*_Test_Guide.md
  • docs/测试说明/专项验证/链路延迟测试说明.md