STM32F4-Base/test/host/iec104/iec104_test.c

/*
 * 模块名称：IEC 60870-5-104 被控站协议栈主机侧单元测试
 * 模块功能：在 PC 上对 App/protocol/iec104 全栈（asdu + pts + link）做离线验证。
 *
 * 被测对象：真实源文件（#include 原样纳入）：
 *             iec104_asdu.c + iec104_pts.c + iec104_link.c（B4 协议核心）
 *             prot_set.c + prot_elm.c + phasor.c + sample_ring.c（板端默认源
 *             的链接依赖；定值两段写走**真实 prot_set**）
 *           数据源经 iec104_pts_bind_src 注入假源（YC/YX/YK 可控），
 *           发送经 send_apdu 回调全量捕获，时基由测试注入。
 *
 * 覆盖点（docs/子系统设计/IEC104上行设计说明.md §7）：
 *   TC-IEC104-001 CP56Time2a 往返 / 闰年 / IV / 钳位
 *   TC-IEC104-002 IOA 3B 与短浮点小端往返
 *   TC-IEC104-003 APCI 重组：半帧 / 粘帧 / 坏起始符 / 坏长度
 *   TC-IEC104-004 STARTDT 握手 → RUN
 *   TC-IEC104-005 OPEN 态 I 帧忽略（序号不消费）
 *   TC-IEC104-006 总召全流程：actcon→4 分片（首召 COT=4）→actterm；二召 COT=2；RBT→COT=4
 *   TC-IEC104-007 遥信变位 COV（COT=3）；无效位不触发
 *   TC-IEC104-008 遥测死区 COV（卡 9 起 = 2 点确认）：死区内不发 / 首越只挂起 /
 *                连续第 2 越点上送
 *   TC-IEC104-009 k 窗：12 未确认停发；S 确认后恢复
 *   TC-IEC104-010 w 阈：收满 8 发 S
 *   TC-IEC104-011 t2 到期发 S
 *   TC-IEC104-012 t3 空闲发 TESTFR act；未答 t1 超时 → IDLE；con 清挂起不误杀
 *   TC-IEC104-013 遥控两段式：选择/执行成功；失配 PN；拒绝类选择段即 PN
 *   TC-IEC104-030 遥控 / 操作记录投递（道F task-10 的 104 侧写入点）：未知 IOA、
 *                YK11 选择与执行、YK12 选择 / 执行 / 非法 DPC 各投哪一类哪一句，外加
 *                "拒绝不投操作记录""记录与压板实际状态一致""文案不超 28 字节"三条会
 *                静默变坏但台架看不出的点（YK12 的 set_sealed 失败腿不可达，理由写在
 *                该用例注释里，没有为它伪造定值范围）
 *   TC-IEC104-014 定值两段写（真实 prot_set）：越界 PN；执行后 get_f + selfcheck
 *   TC-IEC104-015 C_RD：YC 命中 / 定值命中 / 未知 IOA COT14+EVI
 *   TC-IEC104-016 C_CS：clock_sync 收正确 epoch；IV → PN；clock_sync 失败 → PN
 *   TC-IEC104-017 未知类型 COT12+EVI；错公共地址 COT13+EVI
 *   TC-IEC104-018 STOPDT：数据停发，TESTFR 仍应答
 *   TC-IEC104-019 序号错 → IDLE（链路故障）
 *   TC-IEC104-020 pts：无效通道 IV / 未就绪 NT / 无效遥信 IV / is_dp / 表尺寸
 *   TC-IEC104-021 C_TS / C_RP actcon
 *   TC-IEC104-022 周期上送 COT=1（YC 组 + 频率）
 *   TC-IEC104-023 k 窗满 COV 不丢事件（pend 暂存，窗开后补发）
 *   —— 以下为「数据可信」卡 9/卡 11（道D，2026-10-25；板端默认源 = 真实
      L2 链 ring→phasor→freq→meas，非桩）——
 *   TC-IEC104-025 板端源读快照（024 号已归 B7 用例）：未发布
 *                IV|NT / 值=基波有效值 / 削顶 CLIPPED
 *                →线上 IV 清零 / 干净路品质 0 / 频率未新鲜 IV
 *   TC-IEC104-026 0x401D 绑频：收敛后 ±0.02 Hz / freq_valid==0 → IV 清零
 *                （卡 11 DoD 原句）
 *   TC-IEC104-027 死区运行时化（卡 10 后 = run_par 真源 + 转发壳）：set/get
 *                + 非法拒 + 运行档压旧档 + 2 点确认/回摆撤销 + 壳清半截确认计数
 *   TC-IEC104-028 品质翻转直报（假源）+ 板端 seq 去重（同帧不计两点）+
 *                换帧只变品质时按集合直报
 *   TC-IEC104-029 卡 10 路由：0x8030/0x8038 命中 / 0x8027 仍归 prot_set /
 *                空隙 COT14 / C_SE 两段式 / k 带拒 / b 单侧 RMW 保 k
 *
 * 通过：全部 TC PASS（main 返回 0）。
 * 创建日期：2026-10-12（B4）
 */
#include <stdint.h>
#include <stdio.h>
#include <string.h>

static int s_total = 0, s_passed = 0, s_failed = 0;

#define CHECK(cond, name) do { \
    s_total++; \
    if (cond) { s_passed++; printf("  [PASS] %s\n", name); } \
    else      { s_failed++; printf("  [FAIL] %s  (line %d)\n", name, __LINE__); } \
} while (0)

#include "iec104_asdu.c"
#include "prot_set.c"
#include "sample_ring.c"
#include "phasor.c"
#include "freq.c"
#include "meas.c"   /* 卡 9：板端默认 YC 源 = L2 遥测快照（真实链，非桩） */

/* ===================== 卡 10 真链桩（同 adc_cal 套件先例） =====================
 * run_par 依赖真实 cfg 引擎与 adc_cal：dbg_log 走 stub/ 计数宏，文件/堆走
 * 内存虚拟盘（cfg_store_* 强符号），adc_input_desc 按 V0.1 权威映射给桩。
 * 顺序敏感：桩头与强符号先于被纳入的 .c。 */
#include "dbg_log.h"      /* stub/ 优先解析：DBG_* → 计数 */
#include <stdlib.h>
#include "cfg_file_store.h"

#define RP_VFS_CAP 8192u

static uint8_t  rp_s_vfs[RP_VFS_CAP];
static size_t   rp_s_vfs_len = 0u;
static uint32_t rp_s_vfs_mtime = 100u;
static int      rp_s_vfs_exists = 0;

void *cfg_store_alloc(size_t size) { return malloc(size); }
void cfg_store_free(void *p_buf) { free(p_buf); }
uint32_t cfg_store_heap_free(void) { return 0u; }

int cfg_store_read(const char *p_path, uint8_t *p_buf, size_t cap, size_t *p_nread) {
    size_t n;

    (void)p_path;
    if (!rp_s_vfs_exists) {
        return -1;
    }
    n = rp_s_vfs_len;
    if (n > cap) {
        n = cap;
    }
    (void)memcpy(p_buf, rp_s_vfs, n);
    *p_nread = n;
    return 0;
}

int cfg_store_write_atomic(const char *p_path, const uint8_t *p_buf, size_t len) {
    (void)p_path;
    if (len > RP_VFS_CAP) {
        return -1;
    }
    (void)memcpy(rp_s_vfs, p_buf, len);
    rp_s_vfs_len = len;
    rp_s_vfs_exists = 1;
    rp_s_vfs_mtime++;
    return 0;
}

int cfg_store_stat(const char *p_path, cfg_file_stat_t *p_st) {
    (void)p_path;
    if (!rp_s_vfs_exists) {
        return -1;
    }
    p_st->size = (uint32_t)rp_s_vfs_len;
    p_st->mtime = rp_s_vfs_mtime;
    return 0;
}

int cfg_store_remove(const char *p_path) {
    (void)p_path;
    rp_s_vfs_exists = 0;
    rp_s_vfs_len = 0u;
    return 0;
}

const char *cfg_store_config_path(void) { return "/config.ini"; }
const char *cfg_store_tmp_path(void) { return "/config.tmp"; }

/* ---- sys_log 桩：只计数自检留痕 ---- */
#include "sys_log.h"

static int rp_s_syslog_count = 0;

void syslog_post(syslog_id_t id, const char *desc) {
    (void)id;
    (void)desc;
    rp_s_syslog_count++;
}

/* ---- syslog_post_quiet 桩：记下投了什么（task-10 遥控 / 操作记录用） ----
 * 真机上 quiet 与 post 的差别只在"投递侧不打日志"，收/丢判据逐条相同；
 * 本套件是协议栈单测，不验投递本身（那归 test/host/sys_log_mcu），只验
 * **板端源在每条返回路径上投了哪一类、哪一句**——所以这里存成环形日志。 */
#define RP_REC_MAX 16u
static uint8_t rp_s_rec_id[RP_REC_MAX];
static char    rp_s_rec_desc[RP_REC_MAX][SYSLOG_DESC_MAX + 1u];
static uint32_t rp_s_rec_n;           /* 累计条数（不回绕，供"一条都没多投"断言） */
static uint32_t rp_s_drop_quiet;      /* 本桩不模拟丢弃，恒 0 */

void syslog_post_quiet(syslog_id_t id, const char *desc) {
    uint32_t slot;
    size_t   dl = 0u;

    if (desc == NULL) {
        return;
    }
    slot = rp_s_rec_n % RP_REC_MAX;
    rp_s_rec_id[slot] = (uint8_t)id;
    while ((dl < SYSLOG_DESC_MAX) && (desc[dl] != '\0')) {
        dl++;
    }
    (void)memcpy(rp_s_rec_desc[slot], desc, dl);
    rp_s_rec_desc[slot][dl] = '\0';
    rp_s_rec_n++;
}

uint32_t syslog_post_dropped(void) { return rp_s_drop_quiet; }

/* 第 k 条（0 起）记录；越界返回 -1 */
static int rp_rec_at(uint32_t k, syslog_id_t id, const char *desc)
{
    if (k >= rp_s_rec_n) {
        return -1;
    }
    return (rp_s_rec_id[k % RP_REC_MAX] == (uint8_t)id)
           && (strcmp(rp_s_rec_desc[k % RP_REC_MAX], desc) == 0) ? 1 : 0;
}

/* 某类记录一共投了几条 */
static uint32_t rp_rec_cnt(syslog_id_t id)
{
    uint32_t i, n = 0u;

    for (i = 0u; (i < rp_s_rec_n) && (i < RP_REC_MAX); i++) {
        if (rp_s_rec_id[i] == (uint8_t)id) {
            n++;
        }
    }
    return n;
}

static void rp_rec_clear(void)
{
    rp_s_rec_n = 0u;
    (void)memset(rp_s_rec_id, 0, sizeof(rp_s_rec_id));
    (void)memset(rp_s_rec_desc, 0, sizeof(rp_s_rec_desc));
}

/* ---- adc_input_desc 桩：V0.1 权威映射（docs/硬件平台/ADC通道映射说明.md） ---- */
#include "adc_input.h"

static const adc_channel_desc_t rp_s_desc[ADC_SEM_COUNT] = {
    { ADC_SRC_TPAFE, 6u },   /* UA = buf[6] */
    { ADC_SRC_STM32, 14u },  /* UB = CH14(PC4) */
    { ADC_SRC_STM32, 3u },   /* UC = CH3 */
    { ADC_SRC_TPAFE, 5u },   /* UN = buf[5] */
    { ADC_SRC_TPAFE, 2u },   /* IA = buf[2] */
    { ADC_SRC_STM32, 6u },   /* IB = CH6 */
    { ADC_SRC_STM32, 1u },   /* IC = CH1 */
    { ADC_SRC_STM32, 2u },   /* IN = CH2 */
    { ADC_SRC_STM32, 5u },   /* TEMP = CH5 */
};

const adc_channel_desc_t *adc_input_desc(adc_semantic_t ch) {
    if ((int)ch < 0 || (unsigned)ch >= (unsigned)ADC_SEM_COUNT) {
        return NULL;
    }
    return &rp_s_desc[(unsigned)ch];
}

/* dbg 计数定义（stub/dbg_log.h 声明 extern） */
int g_dbgstub104_err_count = 0;
int g_dbgstub104_info_count = 0;
int g_dbgstub104_debug_count = 0;

#include "cfg_file.c"
#include "adc_cal.c"
#include "run_par.c"
#include "prot_elm.c"
#include "iec104_pts.c"
#include "iec104_link.c"

/* ---------------- 假数据源（定值转发真实 prot_set） ---------------- */
static float    s_f_yc[9];
static int      s_f_yc_rc[9];
static uint64_t s_f_bits;
static uint64_t s_f_valid;
static uint32_t s_f_yk_ioa;
static uint8_t  s_f_yk_dpc;
static uint8_t  s_f_yk_sel;

static int f_yc(uint8_t idx, float *out)
{
    if (idx >= 9u) {
        return -1;
    }
    if (s_f_yc_rc[idx] != 0) {
        return s_f_yc_rc[idx];
    }
    *out = s_f_yc[idx];
    return 0;
}
static uint64_t f_bits(void)  { return s_f_bits; }
static uint64_t f_valid(void) { return s_f_valid; }
static int f_yk(uint32_t ioa, uint8_t dpc, uint8_t sel)
{
    s_f_yk_ioa = ioa;
    s_f_yk_dpc = dpc;
    s_f_yk_sel = sel;
    if (ioa == 0x600Bu) {
        /* YK12 全局软压板（B7）：转真实板端源（prot_set_set_sealed 原子路径） */
        return s_src_yk_exec(ioa, dpc, sel);
    }
    return (ioa == 0x600Au) ? 0 : -1;
}
static int f_set_read(uint32_t addr, float *out)
{
    return s_src_set_read(addr, out);
}
static int f_set_write(uint32_t addr, float v, uint8_t sel)
{
    return s_src_set_write(addr, v, sel);
}
static const iec104_pts_src_t g_fake = {
    f_yc, f_bits, f_valid, f_yk, f_set_read, f_set_write
};

/* ---------------- 发送捕获 + 对时假回调 ---------------- */
#define CAP_MAX 48
#define CAP_SZ  260
static uint8_t  s_cap[CAP_MAX][CAP_SZ];
static int      s_cap_n;
static uint64_t s_clock_ms;
static int      s_clock_rc;

static void cap_send(void *ctx, const uint8_t *apdu, uint16_t len)
{
    (void)ctx;
    if ((s_cap_n < CAP_MAX) && (len <= CAP_SZ)) {
        (void)memcpy(s_cap[s_cap_n], apdu, len);
        s_cap_n++;
    }
}
static int f_clock(void *ctx, uint64_t ms)
{
    (void)ctx;
    s_clock_ms = ms;
    return s_clock_rc;
}
/* B9 时标源假回调：s_epoch_val = UINT64_MAX → 时钟无效（CP56 IV） */
static uint64_t s_epoch_val;
static uint64_t f_epoch(void *ctx)
{
    (void)ctx;
    return s_epoch_val;
}

static iec104_link_t g_lk;
static const iec104_link_cfg_t g_cfg = { 1u, cap_send, f_clock, f_epoch };

/* ---------------- 主站侧模拟（N(R) 单调，照真实主站） ---------------- */
static uint16_t m_ns;
static uint16_t m_nr;

static void m_reset(void)
{
    m_ns = 0u;
    m_nr = 0u;
    s_cap_n = 0;
}
static void feed_u(uint8_t q, uint32_t now)
{
    uint8_t b[6];

    b[0] = 0x68u; b[1] = 4u; b[2] = q; b[3] = 0u; b[4] = 0u; b[5] = 0u;
    iec104_link_on_rx(&g_lk, b, 6u, now);
}
static void feed_i(const uint8_t *asdu, uint16_t len, uint32_t now)
{
    uint8_t  b[6u + 250u];
    uint16_t fs = (uint16_t)(m_ns << 1);
    uint16_t fr = (uint16_t)(m_nr << 1);   /* N(R) 单调（feed_s 推进） */

    b[0] = 0x68u;
    b[1] = (uint8_t)(4u + len);
    b[2] = (uint8_t)(fs & 0xFFu);
    b[3] = (uint8_t)(fs >> 8);
    b[4] = (uint8_t)(fr & 0xFFu);
    b[5] = (uint8_t)(fr >> 8);
    (void)memcpy(&b[6], asdu, len);
    iec104_link_on_rx(&g_lk, b, (uint16_t)(6u + len), now);
    m_ns = (uint16_t)((m_ns + 1u) % 32768u);
}
static void feed_s(uint16_t nr, uint32_t now)
{
    uint8_t b[6];
    uint16_t f = (uint16_t)(nr << 1);

    b[0] = 0x68u; b[1] = 4u; b[2] = 1u; b[3] = 0u;
    b[4] = (uint8_t)(f & 0xFFu);
    b[5] = (uint8_t)(f >> 8);
    m_nr = nr;                            /* 主站确认推进（单调） */
    iec104_link_on_rx(&g_lk, b, 6u, now);
}
static uint16_t mk_asdu(uint8_t *b, uint8_t type, uint8_t vsq, uint8_t cot,
                        uint8_t cot_hi, uint8_t with_ioa, uint32_t ioa,
                        const uint8_t *body, uint16_t blen)
{
    uint16_t n = iec104_asdu_put_hdr(b, type, vsq, cot, cot_hi, 1u);

    if (with_ioa != 0u) {
        iec104_put_ioa(&b[n], ioa);
        n += 3u;
    }
    if (blen > 0u) {
        (void)memcpy(&b[n], body, blen);
        n += blen;
    }
    return n;
}

/* ---------------- 复位 / 握手 ---------------- */
static void reset_all(uint32_t now)
{
    prot_set_init();
    prot_elm_init();
    run_par_init();   /* 卡 10：死区/脏复位到工厂默认（重复注册 -1 走计数桩，无害） */
    iec104_pts_init();
    iec104_pts_bind_src(&g_fake);
    (void)memset(s_f_yc, 0, sizeof(s_f_yc));
    (void)memset(s_f_yc_rc, 0, sizeof(s_f_yc_rc));
    s_f_bits  = 0u;
    s_f_valid = (1uLL << 14) | (1uLL << 15) | (1uLL << 16) | (1uLL << 17)
                | (1uLL << 22) | (1uLL << 30);
    s_clock_rc = 0;
    s_clock_ms = 0u;
    s_epoch_val = 1760234567000ULL;     /* B9：固定时标（2025-10-12 UTC） */
    iec104_link_init(&g_lk, &g_cfg, NULL);
    iec104_link_open(&g_lk, now);
    m_reset();
}
static void handshake(uint32_t now)
{
    feed_u(0x07u, now);                 /* STARTDT act */
}

/* ---------------- 捕获检查 ---------------- */
typedef struct {
    uint8_t       type, vsq, cot, cot_hi, oa;
    uint32_t      ca, ioa;
    const uint8_t *obj;                 /* ioa 之后的信息体 */
    uint16_t      obj_len;
} cap_t;

static int cap_i_count(void)
{
    int k, n = 0;

    for (k = 0; k < s_cap_n; k++) {
        if ((s_cap[k][2] & 0x01u) == 0u) {
            n++;
        }
    }
    return n;
}
static int cap_u_count(uint8_t q)
{
    int k, n = 0;

    for (k = 0; k < s_cap_n; k++) {
        if ((s_cap[k][2] & 0x03u) == 0x03u && s_cap[k][2] == q) {
            n++;
        }
    }
    return n;
}
static int cap_has_s(uint16_t *nr_out)
{
    int k;

    for (k = s_cap_n - 1; k >= 0; k--) {
        const uint8_t *p = s_cap[k];

        if ((p[2] & 0x03u) == 0x01u) {
            *nr_out = (uint16_t)(((uint16_t)p[4] | ((uint16_t)p[5] << 8)) >> 1);
            return 1;
        }
    }
    return 0;
}
static int cap_i(int n, cap_t *o)
{
    int k, seen = 0;

    for (k = 0; k < s_cap_n; k++) {
        const uint8_t    *p = s_cap[k];
        uint16_t          lf = p[1];
        iec104_asdu_hdr_t h;

        if ((p[2] & 0x01u) != 0u) {
            continue;
        }
        if (seen == n) {
            if (iec104_asdu_parse_hdr(&p[6], (uint16_t)(lf - 4u), &h) != 0) {
                return -1;
            }
            o->type = h.type;
            o->vsq  = h.vsq;
            o->cot  = h.cot;
            o->cot_hi = h.cot_hi;
            o->oa   = h.oa;
            o->ca   = h.ca;
            if (h.obj_len >= 3u) {
                o->ioa = iec104_get_ioa(h.obj);
                o->obj = h.obj + 3u;
                o->obj_len = (uint16_t)(h.obj_len - 3u);
            } else {
                o->ioa = 0u;
                o->obj = h.obj;
                o->obj_len = 0u;
            }
            return 0;
        }
        seen++;
    }
    return -1;
}

/* ============================ 测试用例 ============================ */

static void tc_cp56(void)
{
    uint8_t  b[7];
    uint64_t e1 = 946684800000ULL;      /* 2000-01-01 00:00:00.000 */
    uint64_t e2 = 1709188496789ULL;     /* 2024-02-29 06:34:56.789（闰日） */
    uint64_t back = 0u;
    int      rc;

    iec104_epoch_ms_to_cp56(e1, b);
    rc = iec104_cp56_to_epoch_ms(b, &back);
    CHECK((rc == 0) && (back == e1), "TC-IEC104-001 CP56 round trip on 2000-01-01");
    iec104_epoch_ms_to_cp56(e2, b);
    back = 0u;
    rc = iec104_cp56_to_epoch_ms(b, &back);
    CHECK((rc == 0) && (back == e2), "TC-IEC104-001 CP56 round trip on the leap day 2024-02-29");
    b[2] |= 0x80u;
    CHECK(iec104_cp56_to_epoch_ms(b, &back) == -2, "TC-IEC104-001 IV -> -2");
    iec104_epoch_ms_to_cp56(0u, b);     /* 早于 2000 → 钳位 */
    back = 0u;
    (void)iec104_cp56_to_epoch_ms(b, &back);
    CHECK(back == e1, "TC-IEC104-001 a value before 2000 is clamped");
}

static void tc_ioa_float(void)
{
    uint8_t b[8];

    iec104_put_ioa(b, 0x123456u);
    CHECK((iec104_get_ioa(b) == 0x123456u) && (b[0] == 0x56u) && (b[1] == 0x34u)
          && (b[2] == 0x12u), "TC-IEC104-002 IOA is 3 bytes little endian");
    iec104_put_float(b, 1.0f);
    CHECK((b[0] == 0x00u) && (b[1] == 0x00u) && (b[2] == 0x80u)
          && (b[3] == 0x3Fu), "TC-IEC104-002 float in IEEE754 little endian");
    iec104_put_float(b, -12.5f);
    CHECK(iec104_get_float(b) == -12.5f, "TC-IEC104-002 float round trip");
}

static void tc_apci(void)
{
    uint32_t now = 1000u;

    reset_all(now);
    {
        static const uint8_t b[6] = { 0x68u, 4u, 0x07u, 0u, 0u, 0u };

        iec104_link_on_rx(&g_lk, b, 3u, now);
        CHECK(cap_u_count(0x0Bu) == 0, "TC-IEC104-003 a half frame triggers nothing");
        iec104_link_on_rx(&g_lk, &b[3], 3u, now);
        CHECK(cap_u_count(0x0Bu) == 1, "TC-IEC104-003 a half frame is reassembled then con");
    }
    {
        static const uint8_t b[12] = {
            0x68u, 4u, 0x43u, 0u, 0u, 0u,   /* TESTFR act */
            0x68u, 4u, 0x13u, 0u, 0u, 0u    /* STOPDT  act */
        };

        iec104_link_on_rx(&g_lk, b, 12u, now);
        CHECK((cap_u_count(0x83u) == 1)
              && (iec104_link_state(&g_lk) == IEC104_ST_STOPPED),
              "TC-IEC104-003 a coalesced frame is handled one by one and STOPDT takes effect");
    }
    reset_all(now);
    {
        static const uint8_t b[6] = { 0x69u, 4u, 0x07u, 0u, 0u, 0u };

        iec104_link_on_rx(&g_lk, b, 6u, now);
        CHECK(iec104_link_state(&g_lk) == IEC104_ST_IDLE, "TC-IEC104-003 a bad start byte -> IDLE");
    }
    reset_all(now);
    {
        static const uint8_t b[6] = { 0x68u, 3u, 0x07u, 0u, 0u, 0u };

        iec104_link_on_rx(&g_lk, b, 6u, now);
        CHECK(iec104_link_state(&g_lk) == IEC104_ST_IDLE, "TC-IEC104-003 a bad length -> IDLE");
    }
}

static void tc_startdt(void)
{
    uint32_t now = 1000u;

    reset_all(now);
    CHECK(iec104_link_state(&g_lk) == IEC104_ST_OPEN, "TC-IEC104-004 open -> OPEN");
    handshake(now);
    CHECK((cap_u_count(0x0Bu) == 1)
          && (iec104_link_state(&g_lk) == IEC104_ST_RUN), "TC-IEC104-004 STARTDT -> RUN");
}

static void tc_open_ignore(void)
{
    uint32_t now = 1000u;
    uint8_t  a[16];
    uint16_t n;

    reset_all(now);
    n = mk_asdu(a, IEC104_T_C_RD_NA_1, 1u, IEC104_COT_REQ, 0u, 1u, 0x4011u, NULL, 0u);
    feed_i(a, n, now);
    CHECK((cap_i_count() == 0) && (iec104_link_state(&g_lk) == IEC104_ST_OPEN),
          "TC-IEC104-005 an I frame in OPEN state is ignored");
    handshake(now);
    m_ns = 0u;                          /* OPEN 忽略不消费序号 → 主站仍从 0 起 */
    feed_i(a, n, now);                  /* ns=0 仍有效（序号未被消费） */
    CHECK(cap_i_count() == 1, "TC-IEC104-005 after RUN the same ns is answered normally");
}

static void tc_interrogation(void)
{
    uint32_t now = 5000u;
    uint8_t  a[32];
    uint8_t  body[1];
    uint16_t n;
    cap_t    c;

    reset_all(now);
    s_f_yc[0] = 111.0f;
    s_f_yc_rc[1] = -1;                  /* idx1（1Ub）无效通道 */
    handshake(now);
    body[0] = IEC104_RQT_GROUP1;
    n = mk_asdu(a, IEC104_T_C_IC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0u, body, 1u);
    feed_i(a, n, now);
    CHECK((cap_i_count() == 1) && (cap_i(0, &c) == 0) && (c.type == 100u)
          && (c.cot == IEC104_COT_ACTCON), "TC-IEC104-006 actcon is sent right away, COT7");
    iec104_link_poll(&g_lk, now);
    CHECK(cap_i_count() == 5, "TC-IEC104-006 the first poll uses the whole budget of 4 frames");
    CHECK((cap_i(1, &c) == 0) && (c.type == 3u) && (c.cot == IEC104_COT_INIT)
          && (c.vsq == (uint8_t)(IEC104_VSQ_SQ | 4u)) && (c.ioa == 1u),
          "TC-IEC104-006 YX double-point group, first call COT=4");
    CHECK((cap_i(2, &c) == 0) && (c.type == 1u)
          && (c.vsq == (uint8_t)(IEC104_VSQ_SQ | 29u)) && (c.ioa == 5u),
          "TC-IEC104-006 YX single-point group with 29 points");
    CHECK((cap_i(3, &c) == 0) && (c.type == 13u)
          && (c.vsq == (uint8_t)(IEC104_VSQ_SQ | 8u)) && (c.ioa == 0x4011u)
          && (c.obj_len == 40u), "TC-IEC104-006 YC group of 8 points, 40 bytes");
    if (cap_i(3, &c) == 0) {
        CHECK((iec104_get_float(c.obj) == 111.0f) && (c.obj[4] == 0u),
              "TC-IEC104-006 YC value 111.0 with QDS=0");
        CHECK(c.obj[9] == IEC104_QDS_IV, "TC-IEC104-006 an invalid channel sets QDS=IV");
    }
    CHECK((cap_i(4, &c) == 0) && (c.ioa == 0x401Du) && (c.vsq == 1u),
          "TC-IEC104-006 frequency as a single point with SQ=0");
    iec104_link_poll(&g_lk, now + 100u);
    CHECK((cap_i_count() == 6) && (cap_i(5, &c) == 0) && (c.type == 100u)
          && (c.cot == IEC104_COT_ACTTERM), "TC-IEC104-006 actterm closes the sequence");
    /* 二召：init 已清 → COT=2 */
    n = mk_asdu(a, IEC104_T_C_IC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0u, body, 1u);
    feed_i(a, n, now + 200u);
    iec104_link_poll(&g_lk, now + 200u);
    CHECK((cap_i(7, &c) == 0) && (c.type == 3u) && (c.cot == IEC104_COT_BG_SCAN),
          "TC-IEC104-006 second call COT=2");
    /* RBT 位 → COT=4（actcon3 是第 12 个未确认帧 → 先 S 确认窗才开） */
    n = mk_asdu(a, IEC104_T_C_IC_NA_1, 1u, IEC104_COT_ACT, IEC104_COT_BIT_RBT,
                1u, 0u, body, 1u);
    feed_i(a, n, now + 300u);
    feed_s(12u, now + 300u);
    iec104_link_poll(&g_lk, now + 300u);
    CHECK((cap_i(12, &c) == 0) && (c.type == 3u) && (c.cot == IEC104_COT_INIT),
          "TC-IEC104-006 RBT -> COT=4");
}

static void tc_cov_yx(void)
{
    uint32_t now = 1000u;
    cap_t    c;
    uint64_t back;

    reset_all(now);
    handshake(now);
    iec104_link_poll(&g_lk, now);       /* 建快照 */
    CHECK(cap_i_count() == 0, "TC-IEC104-007 the first poll sends nothing spontaneous");
    s_f_bits |= (1uLL << 15);           /* YX16（idx15）动作 */
    iec104_link_poll(&g_lk, now + 100u);
    /* B9：单点 YX 自发 = M_SP_TB_1（30）带 CP56Time2a 时标（SOE 上送路径） */
    CHECK((cap_i_count() == 1) && (cap_i(0, &c) == 0) && (c.type == 30u)
          && (c.cot == IEC104_COT_SPONT) && (c.ioa == 16u)
          && (c.obj_len == 8u) && (c.obj[0] == 1u), "TC-IEC104-007 a YX16 change of state sends COT3 with TB");
    if ((cap_i(0, &c) == 0) && (c.obj_len == 8u)) {
        CHECK(iec104_cp56_to_epoch_ms(&c.obj[1], &back) == 0,
              "TC-IEC104-007 the CP56 time tag decodes");
        CHECK(back == s_epoch_val, "TC-IEC104-007 the time tag equals the epoch_ms source");
    }
    s_f_bits &= ~(1uLL << 15);          /* 复归 */
    iec104_link_poll(&g_lk, now + 200u);
    CHECK((cap_i_count() == 2) && (cap_i(1, &c) == 0) && (c.type == 30u)
          && (c.ioa == 16u) && (c.obj[0] == 0u), "TC-IEC104-007 YX16 is reset and changes again");
    /* B9 IV 路径：时标源无效 → CP56 IV 位如实置位 */
    s_epoch_val = UINT64_MAX;
    s_f_bits |= (1uLL << 16);           /* YX17（idx16）动作 */
    iec104_link_poll(&g_lk, now + 300u);
    CHECK((cap_i_count() == 3) && (cap_i(2, &c) == 0) && (c.type == 30u)
          && (c.ioa == 17u) && ((c.obj[3] & 0x80u) != 0u),
          "TC-IEC104-007 an invalid clock sets the CP56 IV bit");
    s_epoch_val = 1760234567000ULL;
    s_f_bits |= (1uLL << 0);            /* idx0 无效位 → 不触发 */
    iec104_link_poll(&g_lk, now + 400u);
    CHECK(cap_i_count() == 3, "TC-IEC104-007 a change while the IV bit is set triggers nothing");
}

static void tc_cov_yc(void)
{
    uint32_t now = 1000u;
    cap_t    c;

    reset_all(now);
    handshake(now);
    s_f_yc[0] = 100.0f;
    iec104_link_poll(&g_lk, now);       /* 快照 = 100 */
    s_f_yc[0] = 100.4f;                 /* 死区 0.5 V 内（卡 6 二次值口径：0.5 %×100 V，
                                         *   旧拟定码值死区 10 已由「数据可信」卡 6 重定） */
    iec104_link_poll(&g_lk, now + 100u);
    CHECK(cap_i_count() == 0, "TC-IEC104-008 inside the deadband nothing is uploaded");
    s_f_yc[0] = 101.25f;                /* 101.25-100=1.25 > 0.5，第 1 越点 */
    iec104_link_poll(&g_lk, now + 200u);
    CHECK(cap_i_count() == 0, "TC-IEC104-008 first deadband crossing only arms (2-point confirm)");
    iec104_link_poll(&g_lk, now + 300u); /* 第 2 个连续测点仍越 -> 确认上送 */
    CHECK((cap_i_count() == 1) && (cap_i(0, &c) == 0) && (c.type == 13u)
          && (c.cot == IEC104_COT_SPONT) && (c.ioa == 0x4011u)
          && (iec104_get_float(c.obj) == 101.25f),
          "TC-IEC104-008 second consecutive crossing uploads (Card 9 confirm)");
}

static void feed_rd(uint32_t now)
{
    uint8_t  a[16];
    uint16_t n = mk_asdu(a, IEC104_T_C_RD_NA_1, 1u, IEC104_COT_REQ, 0u,
                         1u, 0x4011u, NULL, 0u);

    feed_i(a, n, now);
}

static void tc_k_window(void)
{
    uint32_t now = 1000u;
    int      i;

    reset_all(now);
    handshake(now);
    for (i = 0; i < 12; i++) {
        feed_rd(now);
    }
    CHECK(cap_i_count() == 12, "TC-IEC104-009 the k=12 window caps the outstanding frames");
    feed_rd(now);
    CHECK(cap_i_count() == 12, "TC-IEC104-009 the 13th frame is suppressed by the k window");
    feed_s(12u, now);                   /* 全确认 → 窗开 */
    feed_rd(now);
    CHECK(cap_i_count() == 13, "TC-IEC104-009 sending resumes after the S acknowledgement");
}

static void tc_w_thresh(void)
{
    uint32_t now = 1000u;
    uint16_t nr = 0xFFFFu;
    int      i;

    reset_all(now);
    handshake(now);
    for (i = 0; i < 7; i++) {
        feed_rd(now);
    }
    CHECK(cap_has_s(&nr) == 0, "TC-IEC104-010 after 7 received frames no S has been sent yet");
    feed_rd(now);                       /* 第 8 个 → w 阈 */
    CHECK((cap_has_s(&nr) == 1) && (nr == 8u), "TC-IEC104-010 w=8 -> S with nr=8");
}

static void tc_t2(void)
{
    uint32_t now = 1000u;
    uint16_t nr = 0xFFFFu;

    reset_all(now);
    handshake(now);
    feed_rd(now);                       /* rx_unacked=1，t2 起爆 */
    iec104_link_poll(&g_lk, now + 9999u);
    CHECK(cap_has_s(&nr) == 0, "TC-IEC104-011 no S before t2 expires");
    iec104_link_poll(&g_lk, now + 10001u);
    CHECK((cap_has_s(&nr) == 1) && (nr == 1u), "TC-IEC104-011 S is sent once t2 expires");
}

static void tc_t3_t1(void)
{
    uint32_t now = 1000u;

    reset_all(now);
    handshake(now);
    iec104_link_poll(&g_lk, now + 19999u);
    CHECK(cap_u_count(0x43u) == 0, "TC-IEC104-012 no TESTFR before t3 expires");
    iec104_link_poll(&g_lk, now + 20001u);
    CHECK(cap_u_count(0x43u) == 1, "TC-IEC104-012 TESTFR act is sent once t3 expires");
    iec104_link_poll(&g_lk, now + 20001u + 15001u);
    CHECK(iec104_link_state(&g_lk) == IEC104_ST_IDLE, "TC-IEC104-012 an unanswered TESTFR hits t1 -> IDLE");
    /* con 清挂起 → 不误杀 */
    reset_all(now);
    handshake(now);
    iec104_link_poll(&g_lk, now + 20001u);
    CHECK(cap_u_count(0x43u) == 1, "TC-IEC104-012 after reconnect t3 fires again");
    feed_u(0x83u, now + 20100u);        /* TESTFR con */
    iec104_link_poll(&g_lk, now + 35000u);
    CHECK(iec104_link_state(&g_lk) == IEC104_ST_RUN, "TC-IEC104-012 once con clears the pending frame t1 does not kill it by mistake");
}

static void tc_dc(void)
{
    uint32_t now = 1000u;
    uint8_t  a[16];
    uint8_t  body[1];
    uint16_t n;
    cap_t    c;

    reset_all(now);
    handshake(now);
    body[0] = 0x82u;                    /* S=1, DPC=ON */
    n = mk_asdu(a, IEC104_T_C_DC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0x600Au, body, 1u);
    feed_i(a, n, now);
    CHECK((cap_i(0, &c) == 0) && (c.type == 52u) && (c.cot == IEC104_COT_ACTCON)
          && ((c.cot_hi & IEC104_COT_BIT_PN) == 0u), "TC-IEC104-013 the select phase answers actcon");
    CHECK((s_f_yk_sel == 1u) && (s_f_yk_ioa == 0x600Au), "TC-IEC104-013 the select phase forwards the source");
    body[0] = 0x02u;                    /* 执行 ON */
    n = mk_asdu(a, IEC104_T_C_DC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0x600Au, body, 1u);
    feed_i(a, n, now);
    CHECK((cap_i(1, &c) == 0) && ((c.cot_hi & IEC104_COT_BIT_PN) == 0u)
          && (s_f_yk_sel == 0u), "TC-IEC104-013 the execute phase answers actcon");
    /* 失配：选 ON 执 OFF */
    body[0] = 0x82u;
    n = mk_asdu(a, IEC104_T_C_DC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0x600Au, body, 1u);
    feed_i(a, n, now);
    body[0] = 0x01u;
    n = mk_asdu(a, IEC104_T_C_DC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0x600Au, body, 1u);
    feed_i(a, n, now);
    CHECK((cap_i(3, &c) == 0) && ((c.cot_hi & IEC104_COT_BIT_PN) != 0u),
          "TC-IEC104-013 a mismatching execute phase returns PN");
    /* 拒绝类（YK1）：选择段即 PN */
    body[0] = 0x82u;
    n = mk_asdu(a, IEC104_T_C_DC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0x6000u, body, 1u);
    feed_i(a, n, now);
    CHECK((cap_i(4, &c) == 0) && ((c.cot_hi & IEC104_COT_BIT_PN) != 0u),
          "TC-IEC104-013 a YK without output hardware returns PN in the select phase");
}

/* TC-IEC104-024（B7）：YK12 全局软压板两段式转真（经真实板端源 + 原子封存） */
static void tc_dc_yk12(void)
{
    uint32_t now = 1000u;
    uint8_t  a[16];
    uint8_t  body[1];
    uint16_t n;
    cap_t    c;

    reset_all(now);
    handshake(now);
    CHECK(prot_set_get_ctl(PS_GLOBAL_EN) == 1u, "TC-IEC104-024 soft plates are engaged by default");
    body[0] = 0x81u;                    /* S=1, DPC=OFF：选择段 */
    n = mk_asdu(a, IEC104_T_C_DC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0x600Bu, body, 1u);
    feed_i(a, n, now);
    CHECK((cap_i(0, &c) == 0) && (c.cot == IEC104_COT_ACTCON)
          && ((c.cot_hi & IEC104_COT_BIT_PN) == 0u), "TC-IEC104-024 the YK12 select phase answers actcon");
    CHECK(prot_set_get_ctl(PS_GLOBAL_EN) == 1u, "TC-IEC104-024 the select phase performs no action");
    body[0] = 0x01u;                    /* 执行 OFF */
    n = mk_asdu(a, IEC104_T_C_DC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0x600Bu, body, 1u);
    feed_i(a, n, now);
    CHECK((cap_i(1, &c) == 0) && ((c.cot_hi & IEC104_COT_BIT_PN) == 0u),
          "TC-IEC104-024 the YK12 execute phase answers actcon");
    CHECK(prot_set_get_ctl(PS_GLOBAL_EN) == 0u, "TC-IEC104-024 the execute phase drives the soft plate to the released state");
    CHECK(prot_set_selfcheck() == 0, "TC-IEC104-024 set_sealed seals atomically and selfcheck passes");
    CHECK(prot_set_dirty_peek() == 1u, "TC-IEC104-024 the dirty flag is set for persistence");
    body[0] = 0x82u;                    /* 再投入：选择 ON */
    n = mk_asdu(a, IEC104_T_C_DC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0x600Bu, body, 1u);
    feed_i(a, n, now);
    body[0] = 0x02u;                    /* 执行 ON */
    n = mk_asdu(a, IEC104_T_C_DC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0x600Bu, body, 1u);
    feed_i(a, n, now);
    CHECK((cap_i(3, &c) == 0) && ((c.cot_hi & IEC104_COT_BIT_PN) == 0u),
          "TC-IEC104-024 the engage command executes with actcon");
    CHECK(prot_set_get_ctl(PS_GLOBAL_EN) == 1u, "TC-IEC104-024 the soft plate reaches the engaged state");
    body[0] = 0x80u;                    /* DPC=00 非法：选择段即 PN */
    n = mk_asdu(a, IEC104_T_C_DC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0x600Bu, body, 1u);
    feed_i(a, n, now);
    CHECK((cap_i(4, &c) == 0) && ((c.cot_hi & IEC104_COT_BIT_PN) != 0u),
          "TC-IEC104-024 an invalid DPC returns PN in the select phase");
}

/* TC-IEC104-030（道F task-10）：遥控记录——板端默认源 s_src_yk_exec() 的三条返回
 * 路径各投哪一类记录、投几句、是否顺手投了操作记录。
 * 为什么直接调 s_src_yk_exec 而不是发 ASDU：本套件绑定的是**假源** f_yk，
 * YK11 / 未知 IOA 在 f_yk 里就被短路（只有 YK12 转发到真板端源，见 f_yk），
 * 走 ASDU 反而测不到要验的那两条腿；"ASDU -> link -> pts -> 源"这条转发链
 * 已由 TC-IEC104-013/024 覆盖，不重复。**投递本身**（quiet 通道的收/丢）归
 * test/host/sys_log_mcu，本用例只钉"哪条路径投了哪一条"。
 * 覆盖不到的一条腿（登记，不假装）：YK12 的 rc!=0 分支要 prot_set_set_sealed
 * 返 -1 才进得去，而 PS_GLOBAL_EN 的 min/max 恰好就是本函数会写的 0/1 两值
 * → 该产品路径上不可达，是防御性分支；不为它伪造定值范围（那是改判据）。 */
static void tc_yk_records(void)
{
    uint32_t now = 1000u;

    reset_all(now);
    rp_rec_clear();

    /* 1) 未知 IOA：拒绝，只投一条遥控记录；拒绝没改动任何东西 -> 不该有操作记录 */
    CHECK(s_src_yk_exec(0x6000u, (uint8_t)IEC104_DPC_ON, 1u) == -1,
          "TC-IEC104-030 an IOA without output hardware is still rejected");
    CHECK((rp_s_rec_n == 1u) && (rp_rec_at(0u, SYSLOG_YK, "YK unknown ioa") == 1),
          "TC-IEC104-030 the reject path posts exactly one telecontrol record");
    CHECK(rp_rec_cnt(SYSLOG_OPER) == 0u,
          "TC-IEC104-030 a rejected command posts no operation record");

    /* 2) YK11 选择段：受理但未动作 -> 只有遥控记录 */
    rp_rec_clear();
    CHECK((s_src_yk_exec(0x600Au, (uint8_t)IEC104_DPC_ON, 1u) == 0)
          && (rp_s_rec_n == 1u) && (rp_rec_at(0u, SYSLOG_YK, "YK11 select") == 1),
          "TC-IEC104-030 the YK11 select phase posts a select record and acts on nothing");
    CHECK(rp_rec_cnt(SYSLOG_OPER) == 0u,
          "TC-IEC104-030 the select phase is not an operation yet");

    /* 3) YK11 执行段：遥控记录 + 操作记录各一条，顺序 = 先命令后动作 */
    rp_rec_clear();
    CHECK((s_src_yk_exec(0x600Au, (uint8_t)IEC104_DPC_ON, 0u) == 0)
          && (rp_s_rec_n == 2u)
          && (rp_rec_at(0u, SYSLOG_YK, "YK11 exec") == 1)
          && (rp_rec_at(1u, SYSLOG_OPER, "force reset") == 1),
          "TC-IEC104-030 the YK11 execute phase posts one telecontrol plus one operation record");

    /* 4) YK12 非法双点值：拒绝 + 一条带原因的遥控记录，压板不动 */
    rp_rec_clear();
    CHECK((s_src_yk_exec(0x600Bu, 0u, 0u) == -1) && (rp_s_rec_n == 1u)
          && (rp_rec_at(0u, SYSLOG_YK, "YK12 bad dpc") == 1),
          "TC-IEC104-030 an invalid DPC posts the reason and changes nothing");
    CHECK(prot_set_get_ctl(PS_GLOBAL_EN) == 1u,
          "TC-IEC104-030 the invalid DPC leaves the soft plate engaged");

    /* 5) YK12 执行 OFF：遥控 off + 操作 plate out，且压板真的退出了（记录与事实同步） */
    rp_rec_clear();
    CHECK((s_src_yk_exec(0x600Bu, (uint8_t)IEC104_DPC_OFF, 0u) == 0)
          && (rp_s_rec_n == 2u)
          && (rp_rec_at(0u, SYSLOG_YK, "YK12 exec off") == 1)
          && (rp_rec_at(1u, SYSLOG_OPER, "plate out") == 1),
          "TC-IEC104-030 releasing the soft plate records both the command and the operation");
    CHECK(prot_set_get_ctl(PS_GLOBAL_EN) == 0u,
          "TC-IEC104-030 the record agrees with the plate state the settings layer holds");

    /* 6) YK12 执行 ON：对称的另一半（只测 OFF 的话，两条 desc 写反也发现不了） */
    rp_rec_clear();
    CHECK((s_src_yk_exec(0x600Bu, (uint8_t)IEC104_DPC_ON, 0u) == 0)
          && (rp_rec_at(0u, SYSLOG_YK, "YK12 exec on") == 1)
          && (rp_rec_at(1u, SYSLOG_OPER, "plate in") == 1),
          "TC-IEC104-030 engaging the soft plate records the matching pair");

    /* 7) 选择段不落地：YK12 select 只投一条，压板状态不变 */
    rp_rec_clear();
    CHECK((s_src_yk_exec(0x600Bu, (uint8_t)IEC104_DPC_OFF, 1u) == 0)
          && (rp_s_rec_n == 1u) && (rp_rec_at(0u, SYSLOG_YK, "YK12 select") == 1)
          && (prot_set_get_ctl(PS_GLOBAL_EN) == 1u),
          "TC-IEC104-030 the YK12 select phase records the intent without changing the plate");

    /* 8) 文案长度契约：desc 全是 ROM 常量，任何一条超过 SYSLOG_DESC_MAX 都会在
     *    投递侧被静默截断（屏上少几个字，没人会去数）-> 在单测里钉住。 */
    CHECK((strlen(YK_REC_UNKNOWN) <= SYSLOG_DESC_MAX)
          && (strlen(YK_REC_YK11_EXEC) <= SYSLOG_DESC_MAX)
          && (strlen(YK_REC_YK12_OFF) <= SYSLOG_DESC_MAX)
          && (strlen(YK_REC_YK12_FAIL) <= SYSLOG_DESC_MAX)
          && (strlen(YK_REC_DPC_BAD) <= SYSLOG_DESC_MAX)
          && (strlen(YK_REC_YK12_SEL) <= SYSLOG_DESC_MAX)
          && (strlen(YK_REC_YK11_SEL) <= SYSLOG_DESC_MAX)
          && (strlen(YK_REC_YK12_ON) <= SYSLOG_DESC_MAX),
          "TC-IEC104-030 every telecontrol description fits the 28-byte record field");
    rp_rec_clear();
}

static void tc_se(void)
{
    uint32_t now = 1000u;
    uint8_t  a[24];
    uint8_t  body[5];
    uint16_t n;
    uint32_t addr = g_prot_set_meta[PS_OC1_CUR].comm_addr;   /* 0x8858 */
    cap_t    c;

    reset_all(now);
    handshake(now);
    CHECK(addr == 0x8858u, "TC-IEC104-014 the OC1 current setting communication address");
    iec104_put_float(body, 5.0f);
    body[4] = IEC104_QDC_S;             /* 选择段 */
    n = mk_asdu(a, IEC104_T_C_SE_NC_1, 1u, IEC104_COT_ACT, 0u, 1u, addr, body, 5u);
    feed_i(a, n, now);
    CHECK((cap_i(0, &c) == 0) && (c.type == 50u)
          && ((c.cot_hi & IEC104_COT_BIT_PN) == 0u), "TC-IEC104-014 selecting a setting answers actcon");
    body[4] = 0u;                       /* 执行段 */
    n = mk_asdu(a, IEC104_T_C_SE_NC_1, 1u, IEC104_COT_ACT, 0u, 1u, addr, body, 5u);
    feed_i(a, n, now);
    CHECK((cap_i(1, &c) == 0) && ((c.cot_hi & IEC104_COT_BIT_PN) == 0u),
          "TC-IEC104-014 executing a setting answers actcon");
    CHECK(prot_set_get_f(PS_OC1_CUR) == 5.0f, "TC-IEC104-014 the setting really was written (real prot_set)");
    CHECK(prot_set_selfcheck() == 0, "TC-IEC104-014 sealing after execute keeps selfcheck passing");
    CHECK(prot_set_dirty_peek() == 1u, "TC-IEC104-014 the execute phase sets dirty (B7, waiting to be persisted)");
    iec104_put_float(body, 100000.0f);  /* 越上限 */
    body[4] = IEC104_QDC_S;
    n = mk_asdu(a, IEC104_T_C_SE_NC_1, 1u, IEC104_COT_ACT, 0u, 1u, addr, body, 5u);
    feed_i(a, n, now);
    CHECK((cap_i(2, &c) == 0) && ((c.cot_hi & IEC104_COT_BIT_PN) != 0u),
          "TC-IEC104-014 an out-of-range select phase returns PN");
}

static void tc_rd(void)
{
    uint32_t now = 1000u;
    uint8_t  a[16];
    uint16_t n;
    cap_t    c;

    reset_all(now);
    handshake(now);
    s_f_yc[0] = 222.0f;
    n = mk_asdu(a, IEC104_T_C_RD_NA_1, 1u, IEC104_COT_REQ, 0u, 1u, 0x4011u, NULL, 0u);
    feed_i(a, n, now);
    CHECK((cap_i(0, &c) == 0) && (c.type == 13u) && (c.cot == IEC104_COT_REQ)
          && (iec104_get_float(c.obj) == 222.0f), "TC-IEC104-015 C_RD hits a YC group");
    n = mk_asdu(a, IEC104_T_C_RD_NA_1, 1u, IEC104_COT_REQ, 0u, 1u, 0x8858u, NULL, 0u);
    feed_i(a, n, now);
    CHECK((cap_i(1, &c) == 0) && (c.type == 13u) && (c.ioa == 0x8858u),
          "TC-IEC104-015 C_RD hits a setting");
    n = mk_asdu(a, IEC104_T_C_RD_NA_1, 1u, IEC104_COT_REQ, 0u, 1u, 0x9999u, NULL, 0u);
    feed_i(a, n, now);
    CHECK((cap_i(2, &c) == 0) && (c.type == 102u)
          && (c.cot == IEC104_COT_UNK_IOA) && ((c.oa & 0x80u) != 0u),
          "TC-IEC104-015 an unknown IOA answers COT14 plus EVI");
    n = mk_asdu(a, IEC104_T_C_RD_NA_1, 1u, IEC104_COT_REQ, 0u, 1u, 0u, NULL, 0u);
    feed_i(a, n, now);
    CHECK((cap_i(3, &c) == 0) && (c.cot == IEC104_COT_UNK_IOA),
          "TC-IEC104-015 a local setting item (comm_addr=0) is not addressable (B7)");
}

static void tc_cs(void)
{
    uint32_t now = 1000u;
    uint8_t  a[24];
    uint8_t  cp[7];
    uint16_t n;
    cap_t    c;
    uint64_t e = 1709188496789ULL;

    reset_all(now);
    handshake(now);
    (void)iec104_epoch_ms_to_cp56(e, cp);
    n = mk_asdu(a, IEC104_T_C_CS_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0u, cp, 7u);
    feed_i(a, n, now);
    CHECK((cap_i(0, &c) == 0) && (c.type == 103u)
          && ((c.cot_hi & IEC104_COT_BIT_PN) == 0u) && (s_clock_ms == e),
          "TC-IEC104-016 C_CS syncs the clock with an exact epoch");
    cp[2] |= 0x80u;                     /* IV */
    n = mk_asdu(a, IEC104_T_C_CS_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0u, cp, 7u);
    feed_i(a, n, now);
    CHECK((cap_i(1, &c) == 0) && ((c.cot_hi & IEC104_COT_BIT_PN) != 0u),
          "TC-IEC104-016 CP56 IV -> PN");
    (void)iec104_epoch_ms_to_cp56(e, cp);
    s_clock_rc = -1;                    /* 系统侧拒绝 */
    n = mk_asdu(a, IEC104_T_C_CS_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0u, cp, 7u);
    feed_i(a, n, now);
    CHECK((cap_i(2, &c) == 0) && ((c.cot_hi & IEC104_COT_BIT_PN) != 0u),
          "TC-IEC104-016 a clock_sync failure -> PN");
}

static void tc_err_resp(void)
{
    uint32_t now = 1000u;
    uint8_t  a[16];
    uint16_t n, m;
    cap_t    c;

    reset_all(now);
    handshake(now);
    n = mk_asdu(a, 200u, 1u, IEC104_COT_ACT, 0u, 1u, 0u, NULL, 0u);
    feed_i(a, n, now);
    CHECK((cap_i(0, &c) == 0) && (c.type == 200u) && (c.cot == IEC104_COT_UNK_COT)
          && ((c.oa & 0x80u) != 0u), "TC-IEC104-017 an unknown type answers COT12 plus EVI");
    m = iec104_asdu_put_hdr(a, IEC104_T_C_IC_NA_1, 1u, IEC104_COT_ACT, 0u, 2u);
    a[m] = IEC104_RQT_GROUP1;
    m++;
    feed_i(a, m, now);                  /* ca=2 ≠ 1 */
    CHECK((cap_i(1, &c) == 0) && (c.cot == IEC104_COT_UNK_CA)
          && ((c.oa & 0x80u) != 0u), "TC-IEC104-017 a wrong common address answers COT13 plus EVI");
}

static void tc_stopdt(void)
{
    uint32_t now = 1000u;
    uint8_t  a[16];
    uint8_t  body[1];
    uint16_t n;

    reset_all(now);
    handshake(now);
    feed_u(0x13u, now);                 /* STOPDT act */
    CHECK((cap_u_count(0x23u) == 1)
          && (iec104_link_state(&g_lk) == IEC104_ST_STOPPED), "TC-IEC104-018 STOPDT con");
    body[0] = IEC104_RQT_GROUP1;
    n = mk_asdu(a, IEC104_T_C_IC_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0u, body, 1u);
    feed_i(a, n, now);
    CHECK(cap_i_count() == 0, "TC-IEC104-018 in STOPPED state the data service is off");
    feed_u(0x43u, now);
    CHECK(cap_u_count(0x83u) == 1, "TC-IEC104-018 in STOPPED state TESTFR is still answered");
}

static void tc_seq_err(void)
{
    uint32_t now = 1000u;
    uint8_t  a[16];
    uint16_t n;

    reset_all(now);
    handshake(now);
    m_ns = 5u;                          /* 期望 0，投 5 */
    n = mk_asdu(a, IEC104_T_C_RD_NA_1, 1u, IEC104_COT_REQ, 0u, 1u, 0x4011u, NULL, 0u);
    feed_i(a, n, now);
    CHECK(iec104_link_state(&g_lk) == IEC104_ST_IDLE, "TC-IEC104-019 a sequence error -> IDLE");
}

static void tc_pts(void)
{
    float   v;
    uint8_t q;
    uint8_t d;

    reset_all(1000u);
    CHECK((iec104_pts_yc_count() == 9u) && (iec104_pts_yx_count() == 33u)
          && (iec104_pts_yc_ioa(8u) == 0x401Du), "TC-IEC104-020 table size and IOA layout");
    s_f_yc[0] = 7.5f;
    CHECK((iec104_pts_yc_read(0u, &v, &q) == 0) && (v == 7.5f) && (q == 0u),
          "TC-IEC104-020 a valid YC");
    s_f_yc_rc[1] = -1;
    (void)iec104_pts_yc_read(1u, &v, &q);
    CHECK((v == 0.0f) && (q == IEC104_QDS_IV), "TC-IEC104-020 an invalid channel gives IV");
    s_f_yc_rc[2] = -2;
    (void)iec104_pts_yc_read(2u, &v, &q);
    CHECK(q == IEC104_QDS_NT, "TC-IEC104-020 not ready gives NT");
    iec104_pts_yx_read(0u, &d);
    CHECK(d == IEC104_DIQ_IV, "TC-IEC104-020 an invalid telemetry point gives IV");
    CHECK((iec104_pts_yx_is_dp(0u) == 1u) && (iec104_pts_yx_is_dp(4u) == 0u),
          "TC-IEC104-020 the is_dp boundary");
    s_f_bits = (1uLL << 15);
    iec104_pts_yx_read(15u, &d);
    CHECK(d == 1u, "TC-IEC104-020 a valid telemetry point gives ON");
}

static void tc_ts_rp(void)
{
    uint32_t now = 1000u;
    uint8_t  a[16];
    uint8_t  body[2];
    uint16_t n;
    cap_t    c;

    reset_all(now);
    handshake(now);
    body[0] = 0u;
    n = mk_asdu(a, IEC104_T_C_TS_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0u, body, 1u);
    feed_i(a, n, now);
    CHECK((cap_i(0, &c) == 0) && (c.type == 104u) && (c.cot == IEC104_COT_ACTCON),
          "TC-IEC104-021 C_TS actcon");
    n = mk_asdu(a, IEC104_T_C_RP_NA_1, 1u, IEC104_COT_ACT, 0u, 1u, 0u, body, 1u);
    feed_i(a, n, now);
    CHECK((cap_i(1, &c) == 0) && (c.type == 105u) && (c.cot == IEC104_COT_ACTCON),
          "TC-IEC104-021 C_RP actcon");
}

static void tc_periodic(void)
{
    uint32_t now = 1000u;
    cap_t    c;

    reset_all(now);
    handshake(now);
    iec104_link_poll(&g_lk, now + 60001u);
    CHECK(cap_i_count() == 2, "TC-IEC104-022 the cyclic upload takes 2 frames");
    CHECK((cap_i(0, &c) == 0) && (c.type == 13u) && (c.cot == IEC104_COT_PERIODIC)
          && (c.ioa == 0x4011u), "TC-IEC104-022 the cyclic YC group uses COT=1");
    CHECK((cap_i(1, &c) == 0) && (c.ioa == 0x401Du), "TC-IEC104-022 the cyclic frequency point");
}

static void tc_cov_kfull(void)
{
    uint32_t now = 1000u;
    int      i;
    cap_t    c;

    reset_all(now);
    handshake(now);
    iec104_link_poll(&g_lk, now);       /* 先建快照（首 poll 只建不算变位） */
    for (i = 0; i < 12; i++) {
        feed_rd(now);                   /* k 窗占满 */
    }
    s_f_bits |= (1uLL << 14);           /* YX15 变位 */
    iec104_link_poll(&g_lk, now + 100u);
    CHECK(cap_i_count() == 12, "TC-IEC104-023 with k full nothing spontaneous can go out");
    feed_s(12u, now + 200u);            /* 窗开 */
    iec104_link_poll(&g_lk, now + 300u);
    CHECK((cap_i_count() == 13) && (cap_i(12, &c) == 0) && (c.ioa == 15u)
          && (c.cot == IEC104_COT_SPONT), "TC-IEC104-023 once the window opens the backlogged event is sent, none lost");
}

/* ========== 卡 9/卡 11：板端默认源（真实 L2 链：ring→phasor→freq→meas） ========== */

/* 与 App/task/adc_task.c 同型的单拍编排：压环 → phasor_run →（可选 freq_run）。
 * 9 路同幅错相正弦（整周波 → 各路基波有效值 = A/√2，与相位无关，期望好算） */
static double s_ph2 = 0.0;
static void snap_beats(int n, double amp, int run_freq)
{
    float f[ADC_SEM_COUNT];
    int   i;
    int   s;

    for (i = 0; i < n; i++) {
        for (s = 0; s < (int)ADC_SEM_TEMP; s++) {
            f[s] = (float)(amp * sin(s_ph2 + (double)s * 0.35));
        }
        f[ADC_SEM_TEMP] = 1234.0f;
        s_ph2 += 2.0 * 3.14159265358979323846 * 50.0 / 1000.0;   /* 50 Hz */
        (void)sample_ring_push_frame(f, (uint8_t)ADC_SEM_COUNT);
        phasor_run();
        if (run_freq != 0) {
            freq_run();
        }
    }
}
/* 200 ms 发布拍（读同拍 freq 状态，adc_task v3.2 编排的镜像） */
static void snap_pub(uint32_t ms, uint32_t clip_mask)
{
    meas_tick(ms, freq_valid(), freq_last(), clip_mask);
}

static void tc_pts_snap(void)
{
    float   v;
    uint8_t q;

    reset_all(1000u);
    iec104_pts_bind_src(NULL);       /* 板端默认源 = 真实快照链 */
    (void)phasor_init();             /* 环 + 相量双区清零 */
    (void)meas_init();
    CHECK((iec104_pts_yc_read(0u, &v, &q) == -1)
          && (q == (uint8_t)(IEC104_QDS_IV | IEC104_QDS_NT)) && (v == 0.0f),
          "TC-IEC104-025 before first publish -> IV|NT, value zero");
    snap_beats(20, 100.0, 0);
    snap_pub(200u, 0xE6u);           /* 削顶位图同板端默认构建（cl=0xE6） */
    CHECK((iec104_pts_yc_read(0u, &v, &q) == 0) && (q == 0u)
          && (fabsf(v - 70.711f) < 0.1f),
          "TC-IEC104-025 UA = snapshot fundamental RMS (engineering domain)");
    CHECK((iec104_pts_yc_read(3u, &v, &q) == 0) && (q == 0u),
          "TC-IEC104-025 UN (bit3 not in 0xE6) stays valid");
    CHECK((iec104_pts_yc_read(4u, &v, &q) == 0) && (q == 0u),
          "TC-IEC104-025 IA valid");
    CHECK((iec104_pts_yc_read(1u, &v, &q) == -1) && (q == IEC104_QDS_IV)
          && (v == 0.0f), "TC-IEC104-025 clipped UB: CLIPPED maps to wire IV, value zero");
    CHECK((iec104_pts_yc_read(2u, &v, &q) == -1) && (q == IEC104_QDS_IV),
          "TC-IEC104-025 clipped UC IV");
    CHECK((iec104_pts_yc_read(5u, &v, &q) == -1) && (q == IEC104_QDS_IV),
          "TC-IEC104-025 clipped IB IV");
    CHECK((iec104_pts_yc_read(8u, &v, &q) == -1) && (q == IEC104_QDS_IV),
          "TC-IEC104-025 freq point published but not fresh -> IV (Card 11 rule)");
}

static void tc_pts_freq(void)
{
    float   v;
    uint8_t q;
    int     k;

    reset_all(1000u);
    iec104_pts_bind_src(NULL);
    (void)phasor_init();
    (void)freq_init();
    (void)meas_init();
    for (k = 0; k < 5; k++) {           /* 100 拍：测频启动收敛需 20 拍 */
        snap_beats(20, 100.0, 1);
        snap_pub((uint32_t)(k + 1) * 200u, 0u);
    }
    CHECK(freq_valid() == 1u, "TC-IEC104-026 drive precondition: freq converged");
    CHECK((iec104_pts_yc_read(8u, &v, &q) == 0) && (q == 0u)
          && (fabsf(v - 50.0f) <= 0.02f),
          "TC-IEC104-026 0x401D carries freq reading within 0.02 Hz of synthetic 50.000");
    for (k = 0; k < 3; k++) {           /* 浮空：幅值门落下 */
        snap_beats(20, 0.0, 1);
        snap_pub((uint32_t)(6 + k) * 200u, 0u);
    }
    CHECK((freq_valid() == 0u) && (iec104_pts_yc_read(8u, &v, &q) == -1)
          && (q == IEC104_QDS_IV) && (v == 0.0f),
          "TC-IEC104-026 freq_valid==0 -> IV with zeroed value (Card 11 DoD)");
}

static void tc_db_runtime(void)
{
    iec104_pts_cov_t cov;

    reset_all(1000u);                   /* 假源在场 = 每次 cov_check 一测点 */
    CHECK((iec104_pts_yc_set_deadband(0u, 2.0f) == 0)
          && (iec104_pts_yc_deadband(0u) == 2.0f),
          "TC-IEC104-027 runtime deadband write + readback");
    CHECK((iec104_pts_yc_set_deadband(9u, 1.0f) == -1)
          && (iec104_pts_yc_set_deadband(0u, -0.1f) == -1)
          && (iec104_pts_yc_deadband(0u) == 2.0f),
          "TC-IEC104-027 bad idx / negative rejected, RAM untouched");
    CHECK(iec104_pts_yc_deadband(8u) == 0.5f, "TC-IEC104-027 freq point ROM default kept");
    s_f_yc[0] = 100.0f;
    iec104_pts_cov_check(&cov);         /* 建线 rep=100（档 2.0） */
    s_f_yc[0] = 101.0f;                 /* 越旧档 0.5、未越运行档 2.0 */
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0001u) == 0u, "TC-IEC104-027 runtime db gates the old step");
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0001u) == 0u, "TC-IEC104-027 2nd point under 2.0 still silent");

    run_par_init();                     /* 恢复工厂默认档（0.5）——卡 10 复位入口 */
    iec104_pts_init();
    iec104_pts_bind_src(&g_fake);
    s_f_yc[0] = 100.0f;
    iec104_pts_cov_check(&cov);         /* 建线 */
    s_f_yc[0] = 100.6f;                 /* d=0.6 > 0.5，第 1 越 */
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0001u) == 0u, "TC-IEC104-027 crossing arms only (2-point)");
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0001u) != 0u, "TC-IEC104-027 second consecutive crossing confirms");
    s_f_yc[0] = 101.4f;                 /* 新基准 100.6 起 d=0.8 第 1 越 */
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0001u) == 0u, "TC-IEC104-027 pullback test step 1 armed");
    s_f_yc[0] = 100.8f;                 /* 回摆入死区 -> 撤销候选 */
    iec104_pts_cov_check(&cov);
    s_f_yc[0] = 101.4f;                 /* 重新起算：单点不报 */
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0001u) == 0u, "TC-IEC104-027 pullback cleared pending count");
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0001u) != 0u, "TC-IEC104-027 two fresh crossings confirm again");

    /* 壳语义钉（lead 裁⑤）：iec104_pts_yc_set_deadband 成功须清零该点半截确认
     * 计数——若不清，下面第一拍就凑满 2 点直发，与"跨档位重新起算"矛盾 */
    s_f_yc[0] = 100.0f;                 /* rep=101.4 起 d=1.4 > 0.5：第 1 越挂起 */
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0001u) == 0u, "TC-IEC104-027 shell pin arms first");
    iec104_pts_yc_set_deadband(0u, 0.4f);
    s_f_yc[0] = 100.5f;                 /* d=0.9 > 0.4：计数已清则仍只是第 1 越 */
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0001u) == 0u, "TC-IEC104-027 shell clears pending count");
    iec104_pts_cov_check(&cov);         /* 新档连续第 2 越 → 确认 */
    CHECK((cov.yc_changed & 0x0001u) != 0u, "TC-IEC104-027 reconfirms after shell clear");
}

static void tc_cov_qds_seq(void)
{
    iec104_pts_cov_t cov;

    reset_all(1000u);                   /* 假源段：品质翻转 */
    s_f_yc[1] = 50.0f;
    iec104_pts_cov_check(&cov);
    s_f_yc_rc[1] = -1;
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0002u) != 0u, "TC-IEC104-028 valid->IV reported at once");
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0002u) == 0u, "TC-IEC104-028 IV steady state not repeated");
    s_f_yc_rc[1] = 0;
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0002u) != 0u, "TC-IEC104-028 IV->valid recovery reported at once");

    iec104_pts_init();                  /* 板端段：seq 去重 */
    iec104_pts_bind_src(NULL);
    (void)phasor_init();
    (void)meas_init();
    snap_beats(20, 100.0, 0);
    snap_pub(200u, 0u);                 /* seq=1 */
    iec104_pts_cov_check(&cov);         /* 建线帧 */
    CHECK(cov.yc_changed == 0u, "TC-IEC104-028 baseline frame silent");
    snap_beats(20, 200.0, 0);
    snap_pub(400u, 0u);                 /* seq=2：第 1 越点 */
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0001u) == 0u, "TC-IEC104-028 one new frame arms only");
    iec104_pts_cov_check(&cov);
    iec104_pts_cov_check(&cov);         /* 无换帧：不得计为第 2 点 */
    CHECK((cov.yc_changed & 0x0001u) == 0u, "TC-IEC104-028 same frame never counts twice");
    snap_beats(20, 200.0, 0);
    snap_pub(600u, 0u);                 /* seq=3：连续第 2 越点 */
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x0001u) != 0u, "TC-IEC104-028 second new frame confirms");
    snap_pub(800u, 0xE6u);              /* 换帧仅变品质（削顶注入） */
    iec104_pts_cov_check(&cov);
    CHECK((cov.yc_changed & 0x00E6u) == 0x00E6u,
          "TC-IEC104-028 clipped flip per frame reported as a set");
}

/* 卡 10：0x8020~0x8058 读写路由（板端默认源，run_par 表先 / prot_set 后） */
static void tc_pts_rpar_route(void)
{
    float v;

    reset_all(1000u);
    iec104_pts_bind_src(NULL);
    CHECK((iec104_pts_set_read(0x8030u, &v) == 0) && (fabsf(v - 0.5f) < 1e-4f),
          "TC-IEC104-029 0x8030 deadband UA reads factory default");
    CHECK((iec104_pts_set_read(0x8038u, &v) == 0) && (fabsf(v - 0.5f) < 1e-4f),
          "TC-IEC104-029 0x8038 deadband freq reads factory 0.5 Hz");
    /* 0x8027~0x802A = prot_set 告警段（欠压默认 20 V）——run_par 精确匹配
     * 永不覆盖；路由顺序的直接证据 */
    CHECK((iec104_pts_set_read(0x8027u, &v) == 0) && (fabsf(v - 20.0f) < 0.01f),
          "TC-IEC104-029 0x8027 still served by prot_set table");
    CHECK(iec104_pts_set_read(0x8039u, &v) == -1, "TC-IEC104-029 gap address unknown");
    /* C_SE 两段式：选择段校验不提交，执行段落真源 */
    CHECK((iec104_pts_set_write(0x8031u, 0.7f, 1u) == 0)
          && (fabsf(iec104_pts_yc_deadband(1u) - 0.5f) < 1e-4f),
          "TC-IEC104-029 select phase validates without commit");
    CHECK((iec104_pts_set_write(0x8031u, 0.7f, 0u) == 0)
          && (fabsf(iec104_pts_yc_deadband(1u) - 0.7f) < 1e-4f)
          && (run_par_dirty_peek() != 0u),
          "TC-IEC104-029 execute commits and marks dirty");
    CHECK(iec104_pts_set_write(0x8031u, 51.0f, 1u) == -1,
          "TC-IEC104-029 over-range rejected in select");
    /* k/b 覆盖直通 adc_cal（UA 合法带 = ROM x[0.5,2.0] = [76.29,305.17]） */
    CHECK((iec104_pts_set_write(0x8040u, 300.0f, 0u) == 0)
          && (fabsf(adc_cal_k_uv(ADC_SEM_UA) - 300.0f) < 0.01f),
          "TC-IEC104-029 k override lands in adc_cal");
    CHECK(iec104_pts_set_write(0x8040u, 400.0f, 0u) == -1,
          "TC-IEC104-029 k band reject (via adc_cal)");
    CHECK((iec104_pts_set_write(0x8048u, -5.0f, 0u) == 0)
          && (fabsf(adc_cal_b_codes(ADC_SEM_UA) + 5.0f) < 1e-3f)
          && (fabsf(adc_cal_k_uv(ADC_SEM_UA) - 300.0f) < 0.01f),
          "TC-IEC104-029 b single-side write keeps k (RMW)");
    CHECK((iec104_pts_set_read(0x8048u, &v) == 0) && (fabsf(v + 5.0f) < 1e-3f),
          "TC-IEC104-029 b echo via run_par read path");
    run_par_init();   /* 收尾：把 k/b 脏与副本复位留给后续 TC 的干净出厂态 */
}

int main(void)
{
    printf("=== IEC104 Protocol Stack Host Tests ===\n");
    tc_cp56();
    tc_ioa_float();
    tc_apci();
    tc_startdt();
    tc_open_ignore();
    tc_interrogation();
    tc_cov_yx();
    tc_cov_yc();
    tc_k_window();
    tc_w_thresh();
    tc_t2();
    tc_t3_t1();
    tc_dc();
    tc_dc_yk12();
    tc_yk_records();
    tc_se();
    tc_rd();
    tc_cs();
    tc_err_resp();
    tc_stopdt();
    tc_seq_err();
    tc_pts();
    tc_ts_rp();
    tc_periodic();
    tc_cov_kfull();
    tc_pts_snap();
    tc_pts_freq();
    tc_db_runtime();
    tc_cov_qds_seq();
    tc_pts_rpar_route();
    printf("=== IEC104 Tests: %d/%d PASSED (failed=%d) ===\n",
           s_passed, s_total, s_failed);
    return (s_failed == 0) ? 0 : 1;
}