1332 lines
36 KiB
C
1332 lines
36 KiB
C
/*
|
||
* 模块名称：CH395F SPI以太网协议栈驱动
|
||
* 模块功能：CH395F以太网协议栈芯片SPI驱动实现，提供芯片检测、初始化、
|
||
* 网络参数配置、PHY管理、DHCP、Socket管理及数据收发功能
|
||
* 适用平台：STM32F4系列（SPI2接口）
|
||
* 作者：王建锋
|
||
* 创建日期：2026-03-14
|
||
* 修改记录：
|
||
* 2026-03-14 王建锋 创建初始版本，按代码规范重构
|
||
* 2026-07-18 王建锋 改进write_send_buf/read_recv_buf使用SPI2 DMA批量传输
|
||
*/
|
||
|
||
/* 头文件包含区 - 先包含系统头文件，再包含自定义头文件 */
|
||
#include <string.h>
|
||
#include <stdio.h>
|
||
#include "ch395f.h"
|
||
#include "spi.h"
|
||
#include "usart.h"
|
||
|
||
/*
|
||
* 调试输出配置
|
||
*/
|
||
#define DBG_TAG "[CH395]"
|
||
#include "dbg_log.h"
|
||
|
||
/*
|
||
* 私有宏定义区
|
||
*/
|
||
#define CH395F_CHECK_EXIST_TEST_DATA 0x57U /* 芯片检测测试数据 */
|
||
#define CH395F_RESET_DELAY_MS 20U /* 复位后等待延时（ms） */
|
||
#define CH395F_INIT_TIMEOUT_MS 500U /* 初始化超时时间（ms） */
|
||
#define CH395F_SPI_BEGIN_DELAY_MS 1U /* SPI事务开始延时（ms） */
|
||
/* DMA缓冲大小使用ch395f.h中公开的CH395F_SPI_DMA_BUF_SIZE */
|
||
#define CH395F_DMA_BUF_SIZE CH395F_SPI_DMA_BUF_SIZE
|
||
|
||
/*
|
||
* 静态变量定义区 - DMA传输相关
|
||
*/
|
||
static volatile uint8_t s_spi2_dma_done = 0U; /* DMA传输完成标志 */
|
||
|
||
__attribute__((aligned(4)))
|
||
static uint8_t s_spi2_dma_tx_buf[CH395F_DMA_BUF_SIZE]; /* DMA发送缓冲区 */
|
||
__attribute__((aligned(4)))
|
||
static uint8_t s_spi2_dma_rx_buf[CH395F_DMA_BUF_SIZE]; /* DMA接收缓冲区 */
|
||
|
||
/*
|
||
* 私有函数声明区
|
||
*/
|
||
static void ch395f_spi_begin(void);
|
||
static void ch395f_spi_end(void);
|
||
static void ch395f_spi_dma_transfer(uint16_t len);
|
||
|
||
/*
|
||
* 私有函数定义区
|
||
*/
|
||
|
||
/*
|
||
* 函数功能：启动一次SPI事务（CS高→低）
|
||
* 限定条件：SPI2外设已初始化
|
||
* 函数说明：1. 先将CS置高再置低，满足片选信号最小间隔要求
|
||
* 2. SPI模式下字节间无需额外延时
|
||
*/
|
||
static void ch395f_spi_begin(void) {
|
||
/* CS置高确保空闲状态 */
|
||
HAL_GPIO_WritePin(CH395_SCS_GPIO_Port, CH395_SCS_Pin, GPIO_PIN_SET);
|
||
/* CS置低启动事务（无需额外延时，SPI时序由SCK频率决定） */
|
||
HAL_GPIO_WritePin(CH395_SCS_GPIO_Port, CH395_SCS_Pin, GPIO_PIN_RESET);
|
||
}
|
||
|
||
/*
|
||
* 函数功能：结束一次SPI事务（CS置高）
|
||
* 限定条件：SPI2外设已初始化
|
||
*/
|
||
static void ch395f_spi_end(void) {
|
||
/* CS置高结束事务 */
|
||
HAL_GPIO_WritePin(CH395_SCS_GPIO_Port, CH395_SCS_Pin, GPIO_PIN_SET);
|
||
}
|
||
|
||
/*
|
||
* 函数功能：DMA全双工传输并等待完成
|
||
* 入口参数：len - 传输长度（字节） uint16_t 1 - CH395F_DMA_BUF_SIZE
|
||
* 限定条件：1. s_spi2_dma_tx_buf中已填充待发送数据
|
||
* 2. 需确保DMA传输缓冲区已对齐到4字节边界
|
||
* 函数说明：1. 发送s_spi2_dma_tx_buf内容，同时接收数据存入s_spi2_dma_rx_buf
|
||
* 2. 阻塞等待DMA完成回调置标志位
|
||
* 3. 超时（1秒）时强制中止SPI DMA并打印错误信息
|
||
* 4. 传输完成后检查SPI错误码并清除溢出标志
|
||
*/
|
||
static void ch395f_spi_dma_transfer(uint16_t len) {
|
||
HAL_StatusTypeDef status;
|
||
uint32_t tickstart;
|
||
volatile uint32_t loop_cnt = 0U;
|
||
|
||
s_spi2_dma_done = 0U;
|
||
status = HAL_SPI_TransmitReceive_DMA(&hspi2, s_spi2_dma_tx_buf, s_spi2_dma_rx_buf, len);
|
||
if (status != HAL_OK) {
|
||
DBG_ERROR("HAL_SPI_TransmitReceive_DMA FAIL: %d, SPI_State=%d, SPI_Error=0x%lX, DMA_State=%d",
|
||
(int)status,
|
||
(int)hspi2.State,
|
||
hspi2.ErrorCode,
|
||
(int)hspi2.hdmarx->State);
|
||
return;
|
||
}
|
||
|
||
tickstart = HAL_GetTick();
|
||
while (s_spi2_dma_done == 0U) {
|
||
loop_cnt++;
|
||
if ((HAL_GetTick() - tickstart) > 1000U) {
|
||
DBG_ERROR("TIMEOUT after 1s, len=%d, loop=%lu, SPI_State=%d, SPI_Error=0x%lX",
|
||
(int)len, loop_cnt,
|
||
(int)hspi2.State,
|
||
hspi2.ErrorCode);
|
||
DBG_ERROR(" DMA_RX: State=%d, Dir=%lu, CNT=%lu",
|
||
(int)hspi2.hdmarx->State,
|
||
hspi2.hdmarx->Init.Direction,
|
||
__HAL_DMA_GET_COUNTER(hspi2.hdmarx));
|
||
DBG_ERROR(" DMA_TX: State=%d, Dir=%lu, CNT=%lu",
|
||
(int)hspi2.hdmatx->State,
|
||
hspi2.hdmatx->Init.Direction,
|
||
__HAL_DMA_GET_COUNTER(hspi2.hdmatx));
|
||
DBG_ERROR(" SPI2_CR1=0x%lX, CR2=0x%lX, SR=0x%lX",
|
||
SPI2->CR1, SPI2->CR2, SPI2->SR);
|
||
/* 强制中止SPI2 DMA状态，避免死锁 */
|
||
HAL_SPI_Abort(&hspi2);
|
||
return;
|
||
}
|
||
}
|
||
|
||
/* 检查传输是否成功：SPI错误码必须为0 */
|
||
if (hspi2.ErrorCode != 0U) {
|
||
DBG_INFO("SPI DMA done with errors: ErrorCode=0x%lX, SPI_State=%d",
|
||
hspi2.ErrorCode, (int)hspi2.State);
|
||
__HAL_SPI_CLEAR_OVRFLAG(&hspi2);
|
||
}
|
||
}
|
||
|
||
/*
|
||
* 函数功能：SPI传输完成回调函数
|
||
* 入口参数：hspi - SPI句柄指针 SPI_HandleTypeDef*
|
||
* 函数说明：由HAL SPI驱动在DMA TX+RX完成后调用
|
||
*/
|
||
/* SPI1 DMA完成标志（定义在gd5f2gq5ue.c中） */
|
||
extern volatile uint8_t g_spi1_dma_done;
|
||
|
||
void HAL_SPI_TxRxCpltCallback(SPI_HandleTypeDef *hspi) {
|
||
if (hspi->Instance == SPI2) {
|
||
s_spi2_dma_done = 1U;
|
||
} else if (hspi->Instance == SPI1) {
|
||
g_spi1_dma_done = 1U;
|
||
}
|
||
}
|
||
|
||
/*
|
||
* 函数功能：SPI错误回调函数
|
||
* 入口参数：hspi - SPI句柄指针 SPI_HandleTypeDef*
|
||
* 函数说明：由HAL SPI驱动在DMA传输错误时调用，释放等待者
|
||
*/
|
||
void HAL_SPI_ErrorCallback(SPI_HandleTypeDef *hspi) {
|
||
if (hspi->Instance == SPI2) {
|
||
s_spi2_dma_done = 1U;
|
||
} else if (hspi->Instance == SPI1) {
|
||
g_spi1_dma_done = 1U;
|
||
}
|
||
}
|
||
|
||
/*
|
||
* 公共函数定义区
|
||
*/
|
||
|
||
/*
|
||
* 函数功能：向CH395写入一个命令字节
|
||
* 入口参数：cmd - 命令字节 uint8_t 0x00 - 0xFF
|
||
* 返回值：命令回显字节 uint8_t
|
||
* 限定条件：必须在ch395f_spi_begin()和ch395f_spi_end()之间调用
|
||
* 函数说明：SPI模式下命令和数据字节之间无需间隔
|
||
*/
|
||
uint8_t ch395f_write_cmd(uint8_t cmd) {
|
||
uint8_t rx_data;
|
||
|
||
/* 通过SPI发送命令并接收回显 */
|
||
HAL_SPI_TransmitReceive(&hspi2, &cmd, &rx_data, 1, HAL_MAX_DELAY);
|
||
return rx_data;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：向CH395写入一个数据字节
|
||
* 入口参数：data - 数据字节 uint8_t 0x00 - 0xFF
|
||
* 返回值：数据回显字节 uint8_t
|
||
* 限定条件：必须在ch395f_spi_begin()和ch395f_spi_end()之间调用
|
||
*/
|
||
uint8_t ch395f_write_data(uint8_t data) {
|
||
uint8_t rx_data;
|
||
|
||
/* 通过SPI发送数据并接收回显 */
|
||
HAL_SPI_TransmitReceive(&hspi2, &data, &rx_data, 1, HAL_MAX_DELAY);
|
||
return rx_data;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：从CH395读取一个数据字节
|
||
* 返回值：接收到的数据字节 uint8_t
|
||
* 限定条件：必须在ch395f_spi_begin()和ch395f_spi_end()之间调用
|
||
* 函数说明：发送0xFF作为SPI时钟源，同时读取芯片返回的数据
|
||
*/
|
||
uint8_t ch395f_read_data(void) {
|
||
uint8_t tx_dummy = 0xFFU;
|
||
uint8_t rx_data;
|
||
|
||
/* 发送0xFF作为时钟源，读取芯片返回数据 */
|
||
HAL_SPI_TransmitReceive(&hspi2, &tx_dummy, &rx_data, 1, HAL_MAX_DELAY);
|
||
return rx_data;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：检测CH395芯片是否存在且通信正常
|
||
* 返回值：CH395F_STATUS_OK - 芯片检测成功 ch395f_status_t
|
||
* CH395F_STATUS_NOT_DETECTED - 芯片未检测到 ch395f_status_t
|
||
* 限定条件：SPI2外设已正确初始化
|
||
* 函数说明：1. 发送CMD_CHECK_EXIST（0x06）后跟测试数据0x57
|
||
* 2. 芯片应返回测试数据的按位取反结果0xA8
|
||
* 3. 回显匹配则返回成功，否则返回未检测到
|
||
*/
|
||
ch395f_status_t ch395f_check_exist(void) {
|
||
uint8_t test_data = CH395F_CHECK_EXIST_TEST_DATA;
|
||
uint8_t reply_data;
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送检测命令 */
|
||
ch395f_write_cmd(CH395F_CMD_CHECK_EXIST);
|
||
|
||
/* 发送测试数据 */
|
||
ch395f_write_data(test_data);
|
||
|
||
/* 读取芯片回复 */
|
||
reply_data = ch395f_read_data();
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
|
||
/* 验证回复是否为测试数据的按位取反 */
|
||
if (reply_data == (uint8_t)(~test_data)) {
|
||
return CH395F_STATUS_OK;
|
||
}
|
||
|
||
return CH395F_STATUS_NOT_DETECTED;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：读取CH395芯片版本号
|
||
* 返回值：版本字节（bits 5:0 = 版本号） uint8_t
|
||
* 限定条件：芯片已通过ch395f_check_exist()检测
|
||
*/
|
||
uint8_t ch395f_get_version(void) {
|
||
uint8_t version;
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送版本读取命令 */
|
||
ch395f_write_cmd(CH395F_CMD_GET_IC_VER);
|
||
|
||
/* 读取版本号 */
|
||
version = ch395f_read_data();
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
|
||
return version;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：获取远程IP地址和端口号
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* p_buf - 6字节输出缓冲区指针（4字节IP + 2字节端口） uint8_t*
|
||
* 限定条件：1. p_buf不可为NULL
|
||
* 2. 需在TCP Server模式下连接建立后调用
|
||
* 函数说明：IP和端口均为低字节在前
|
||
*/
|
||
void ch395f_get_remot_ipp(uint8_t sock, uint8_t *p_buf) {
|
||
uint8_t i;
|
||
|
||
/* 检查输入参数合法性 */
|
||
if (p_buf == NULL) {
|
||
return;
|
||
}
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送获取远程IP和端口命令 */
|
||
ch395f_write_cmd(CH395F_CMD_GET_REMOT_IPP_SN);
|
||
|
||
/* 发送Socket索引 */
|
||
ch395f_write_data(sock);
|
||
|
||
/* 读取4字节IP地址 */
|
||
for (i = 0; i < 4; i++) {
|
||
p_buf[i] = ch395f_read_data();
|
||
}
|
||
|
||
/* 读取2字节端口号 */
|
||
for (i = 4; i < 6; i++) {
|
||
p_buf[i] = ch395f_read_data();
|
||
}
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置CH395功能参数
|
||
* 入口参数：para - 4字节功能参数 uint32_t
|
||
* 限定条件：必须在ch395f_init()之前调用
|
||
*/
|
||
void ch395f_set_fun_para(uint32_t para) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置功能参数命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_FUN_PARA);
|
||
|
||
/* 发送4字节参数（低字节在前） */
|
||
ch395f_write_data((uint8_t)(para));
|
||
ch395f_write_data((uint8_t)(para >> 8));
|
||
ch395f_write_data((uint8_t)(para >> 16));
|
||
ch395f_write_data((uint8_t)(para >> 24));
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置TCP最大分段大小（MSS）
|
||
* 入口参数：mss - MSS值 uint16_t 60 - 1460
|
||
* 限定条件：必须在ch395f_init()之前调用
|
||
*/
|
||
void ch395f_set_tcp_mss(uint16_t mss) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置TCP MSS命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_TCP_MSS);
|
||
|
||
/* 发送2字节MSS值（低字节在前） */
|
||
ch395f_write_data(mss & 0xFFU);
|
||
ch395f_write_data((mss >> 8) & 0xFFU);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置Socket接收缓冲区
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* start_block - 起始块地址 uint8_t
|
||
* block_count - 块数量 uint8_t
|
||
* 限定条件：必须在OPEN_SOCKET_SN之前调用
|
||
*/
|
||
void ch395f_set_recv_buf(uint8_t sock, uint8_t start_block, uint8_t block_count) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置接收缓冲区命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_RECV_BUF);
|
||
|
||
/* 发送Socket索引 */
|
||
ch395f_write_data(sock);
|
||
|
||
/* 发送起始块地址 */
|
||
ch395f_write_data(start_block);
|
||
|
||
/* 发送块数量 */
|
||
ch395f_write_data(block_count);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置Socket发送缓冲区
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* start_block - 起始块地址 uint8_t
|
||
* block_count - 块数量 uint8_t
|
||
* 限定条件：必须在OPEN_SOCKET_SN之前调用
|
||
*/
|
||
void ch395f_set_send_buf(uint8_t sock, uint8_t start_block, uint8_t block_count) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置发送缓冲区命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_SEND_BUF);
|
||
|
||
/* 发送Socket索引 */
|
||
ch395f_write_data(sock);
|
||
|
||
/* 发送起始块地址 */
|
||
ch395f_write_data(start_block);
|
||
|
||
/* 发送块数量 */
|
||
ch395f_write_data(block_count);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：清除Socket接收缓冲区
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* 限定条件：Socket必须已打开
|
||
*/
|
||
void ch395f_clear_recv_buf(uint8_t sock) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送清除接收缓冲区命令 */
|
||
ch395f_write_cmd(CH395F_CMD_CLEAR_RECV_BUF_SN);
|
||
|
||
/* 发送Socket索引 */
|
||
ch395f_write_data(sock);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置TCP KeepAlive空闲时间
|
||
* 入口参数：time - 空闲时间（秒） uint32_t
|
||
* 限定条件：必须在ch395f_init()之前调用
|
||
*/
|
||
void ch395f_set_keepalive_idle(uint32_t time) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置KeepAlive空闲时间命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_KEEPALIVE_IDLE);
|
||
|
||
/* 发送4字节时间值（低字节在前） */
|
||
ch395f_write_data((uint8_t)(time));
|
||
ch395f_write_data((uint8_t)(time >> 8));
|
||
ch395f_write_data((uint8_t)(time >> 16));
|
||
ch395f_write_data((uint8_t)(time >> 24));
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置TCP KeepAlive探测间隔
|
||
* 入口参数：time - 探测间隔（秒） uint32_t
|
||
* 限定条件：必须在ch395f_init()之前调用
|
||
*/
|
||
void ch395f_set_keepalive_intvl(uint32_t time) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置KeepAlive探测间隔命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_KEEPALIVE_INTVL);
|
||
|
||
/* 发送4字节时间值（低字节在前） */
|
||
ch395f_write_data((uint8_t)(time));
|
||
ch395f_write_data((uint8_t)(time >> 8));
|
||
ch395f_write_data((uint8_t)(time >> 16));
|
||
ch395f_write_data((uint8_t)(time >> 24));
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置TCP KeepAlive探测次数
|
||
* 入口参数：cnt - 探测次数 uint8_t
|
||
* 限定条件：必须在ch395f_init()之前调用
|
||
*/
|
||
void ch395f_set_keepalive_cnt(uint8_t cnt) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置KeepAlive探测次数命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_KEEPALIVE_CNT);
|
||
|
||
/* 发送探测次数 */
|
||
ch395f_write_data(cnt);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：使能/禁能指定Socket的KeepAlive功能
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* enable - 使能标志 uint8_t 1 = 使能，0 = 禁能
|
||
* 限定条件：Socket必须已打开
|
||
*/
|
||
void ch395f_set_keepalive_enable(uint8_t sock, uint8_t enable) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置KeepAlive使能命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_KEEPALIVE_SN);
|
||
|
||
/* 发送Socket索引 */
|
||
ch395f_write_data(sock);
|
||
|
||
/* 发送使能标志 */
|
||
ch395f_write_data(enable);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置TCP重传次数
|
||
* 入口参数：cnt - 重传次数 uint8_t 0 = 使用默认值
|
||
* 限定条件：必须在ch395f_init()之前调用
|
||
*/
|
||
void ch395f_set_retrans_count(uint8_t cnt) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置重传次数命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_RETRAN_COUNT);
|
||
|
||
/* 发送重传次数 */
|
||
ch395f_write_data(cnt);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置TCP重传周期
|
||
* 入口参数：period - 重传周期（毫秒） uint16_t
|
||
* 限定条件：必须在ch395f_init()之前调用
|
||
*/
|
||
void ch395f_set_retrans_period(uint16_t period) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置重传周期命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_RETRAN_PERIOD);
|
||
|
||
/* 发送2字节周期值（低字节在前） */
|
||
ch395f_write_data(period & 0xFFU);
|
||
ch395f_write_data((period >> 8) & 0xFFU);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：软件复位CH395芯片
|
||
* 返回值：CH395F_STATUS_OK - 复位成功 ch395f_status_t
|
||
* 限定条件：SPI2外设已正确初始化
|
||
* 函数说明：复位耗时约15ms（TE0），函数内部包含延时等待
|
||
*/
|
||
ch395f_status_t ch395f_reset(void) {
|
||
DBG_INFO("ch395f_reset: spi_begin");
|
||
ch395f_spi_begin();
|
||
|
||
DBG_INFO("ch395f_reset: write_cmd RESET_ALL");
|
||
ch395f_write_cmd(CH395F_CMD_RESET_ALL);
|
||
|
||
DBG_INFO("ch395f_reset: spi_end");
|
||
ch395f_spi_end();
|
||
|
||
DBG_INFO("ch395f_reset: HAL_Delay(%d)", CH395F_RESET_DELAY_MS);
|
||
DBG_INFO("ch395f_reset: tick=%lu basepri=0x%02X", HAL_GetTick(), __get_BASEPRI());
|
||
HAL_Delay(CH395F_RESET_DELAY_MS);
|
||
|
||
DBG_INFO("ch395f_reset: done");
|
||
return CH395F_STATUS_OK;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：查询命令执行状态
|
||
* 返回值：状态字节（CH395F_ERR_SUCCESS / CH395F_ERR_BUSY / ...） uint8_t
|
||
* 限定条件：仅用于耗时较长的命令（如初始化）之后查询
|
||
*/
|
||
uint8_t ch395f_get_cmd_status(void) {
|
||
uint8_t status;
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送状态查询命令 */
|
||
ch395f_write_cmd(CH395F_CMD_GET_CMD_STATUS);
|
||
|
||
/* 读取状态字节 */
|
||
status = ch395f_read_data();
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
|
||
return status;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：轮询等待命令执行完成
|
||
* 入口参数：timeout_ms - 超时时间（毫秒） uint32_t
|
||
* 返回值：命令执行状态（CH395F_ERR_SUCCESS = 成功，CH395F_ERR_BUSY = 超时） uint8_t
|
||
* 限定条件：需在发送耗时较长的命令后调用
|
||
* 函数说明：每20ms查询一次，直到命令完成或超时
|
||
*/
|
||
uint8_t ch395f_poll_cmd_status(uint32_t timeout_ms) {
|
||
uint8_t status;
|
||
uint32_t retry_count = 0U;
|
||
uint32_t max_retries = (timeout_ms + 20U - 1U) / 20U;
|
||
|
||
while (1) {
|
||
HAL_Delay(20U);
|
||
status = ch395f_get_cmd_status();
|
||
|
||
if (status != CH395F_ERR_BUSY) {
|
||
return status;
|
||
}
|
||
|
||
if (++retry_count >= max_retries) {
|
||
return CH395F_ERR_BUSY; /* 超时 */
|
||
}
|
||
}
|
||
}
|
||
|
||
/*
|
||
* 函数功能：初始化CH395（包括MAC、PHY、TCP/IP协议栈）
|
||
* 返回值：CH395F_STATUS_OK - 初始化成功 ch395f_status_t
|
||
* CH395F_STATUS_TIMEOUT - 初始化超时 ch395f_status_t
|
||
* CH395F_STATUS_ERROR - 初始化失败 ch395f_status_t
|
||
* 限定条件：芯片已通过ch395f_reset()复位
|
||
* 函数说明：芯片初始化需约200ms，函数内等待最多4秒
|
||
*/
|
||
ch395f_status_t ch395f_init(void) {
|
||
uint8_t status;
|
||
|
||
ch395f_spi_begin();
|
||
ch395f_write_cmd(CH395F_CMD_INIT_CH395);
|
||
ch395f_spi_end();
|
||
|
||
status = ch395f_poll_cmd_status(4000U);
|
||
|
||
if (status == CH395F_ERR_SUCCESS) {
|
||
return CH395F_STATUS_OK;
|
||
}
|
||
|
||
return (status == CH395F_ERR_BUSY) ? CH395F_STATUS_TIMEOUT : CH395F_STATUS_ERROR;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置CH395的IP地址（低字节在前）
|
||
* 入口参数：p_ip - 4字节IP地址指针 uint8_t* 192.168.x.x格式
|
||
* 限定条件：1. p_ip不可为NULL
|
||
* 2. 芯片已初始化
|
||
*/
|
||
void ch395f_set_ip_addr(uint8_t *p_ip) {
|
||
uint8_t i;
|
||
|
||
/* 检查输入参数合法性 */
|
||
if (p_ip == NULL) {
|
||
return;
|
||
}
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置IP命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_IP_ADDR);
|
||
|
||
/* 逐字节发送IP地址 */
|
||
for (i = 0; i < 4; i++) {
|
||
ch395f_write_data(p_ip[i]);
|
||
}
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置CH395的网关IP地址（低字节在前）
|
||
* 入口参数：p_gwip - 4字节网关IP指针 uint8_t*
|
||
* 限定条件：1. p_gwip不可为NULL
|
||
* 2. 芯片已初始化
|
||
*/
|
||
void ch395f_set_gwip_addr(uint8_t *p_gwip) {
|
||
uint8_t i;
|
||
|
||
/* 检查输入参数合法性 */
|
||
if (p_gwip == NULL) {
|
||
return;
|
||
}
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置网关命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_GWIP_ADDR);
|
||
|
||
/* 逐字节发送网关IP地址 */
|
||
for (i = 0; i < 4; i++) {
|
||
ch395f_write_data(p_gwip[i]);
|
||
}
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置CH395的子网掩码（低字节在前）
|
||
* 入口参数：p_mask - 4字节子网掩码指针 uint8_t*
|
||
* 限定条件：1. p_mask不可为NULL
|
||
* 2. 芯片已初始化
|
||
*/
|
||
void ch395f_set_mask_addr(uint8_t *p_mask) {
|
||
uint8_t i;
|
||
|
||
/* 检查输入参数合法性 */
|
||
if (p_mask == NULL) {
|
||
return;
|
||
}
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置掩码命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_MASK_ADDR);
|
||
|
||
/* 逐字节发送子网掩码 */
|
||
for (i = 0; i < 4; i++) {
|
||
ch395f_write_data(p_mask[i]);
|
||
}
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置CH395的MAC地址（低字节在前，存入EEPROM）
|
||
* 入口参数：p_mac - 6字节MAC地址指针 uint8_t*
|
||
* 限定条件：1. p_mac不可为NULL
|
||
* 2. 芯片已初始化
|
||
* 函数说明：执行耗时约30us（TE5）
|
||
*/
|
||
void ch395f_set_mac_addr(uint8_t *p_mac) {
|
||
uint8_t i;
|
||
|
||
/* 检查输入参数合法性 */
|
||
if (p_mac == NULL) {
|
||
return;
|
||
}
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置MAC命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_MAC_ADDR);
|
||
|
||
/* 逐字节发送MAC地址 */
|
||
for (i = 0; i < 6; i++) {
|
||
ch395f_write_data(p_mac[i]);
|
||
}
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：读取CH395的MAC地址
|
||
* 出口参数：p_mac - 6字节MAC地址缓冲区指针 uint8_t*
|
||
* 限定条件：p_mac不可为NULL
|
||
*/
|
||
void ch395f_get_mac_addr(uint8_t *p_mac) {
|
||
uint8_t i;
|
||
|
||
/* 检查输入参数合法性 */
|
||
if (p_mac == NULL) {
|
||
return;
|
||
}
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送读取MAC命令 */
|
||
ch395f_write_cmd(CH395F_CMD_GET_MAC_ADDR);
|
||
|
||
/* 逐字节读取MAC地址 */
|
||
for (i = 0; i < 6; i++) {
|
||
p_mac[i] = ch395f_read_data();
|
||
}
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：读取IP信息（IP地址 + 子网掩码 + DNS，共20字节）
|
||
* 出口参数：p_buf - 20字节缓冲区指针 uint8_t*
|
||
* 限定条件：p_buf不可为NULL
|
||
*/
|
||
void ch395f_get_ip_inf(uint8_t *p_buf) {
|
||
uint8_t i;
|
||
|
||
/* 检查输入参数合法性 */
|
||
if (p_buf == NULL) {
|
||
return;
|
||
}
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送读取IP信息命令 */
|
||
ch395f_write_cmd(CH395F_CMD_GET_IP_INF);
|
||
|
||
/* 逐字节读取IP信息（共20字节） */
|
||
for (i = 0; i < 20; i++) {
|
||
p_buf[i] = ch395f_read_data();
|
||
}
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：获取PHY连接状态
|
||
* 返回值：PHY状态码（CH395F_PHY_DISCONN / CH395F_PHY_10M_FULL / ...） uint8_t
|
||
* 限定条件：芯片已初始化
|
||
*/
|
||
uint8_t ch395f_get_phy_status(void) {
|
||
uint8_t status;
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送读取PHY状态命令 */
|
||
ch395f_write_cmd(CH395F_CMD_GET_PHY_STATUS);
|
||
|
||
/* 读取PHY状态 */
|
||
status = ch395f_read_data();
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
|
||
return status;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置PHY连接模式
|
||
* 入口参数：phystat - 连接模式 uint8_t 0x20 = 自动协商
|
||
* 限定条件：芯片已初始化
|
||
*/
|
||
void ch395f_set_phy(uint8_t phystat) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置PHY命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_PHY);
|
||
|
||
/* 发送连接模式参数 */
|
||
ch395f_write_data(phystat);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：使能/禁能CH395的PING响应
|
||
* 入口参数：enable - 使能标志 uint8_t 1 = 使能PING响应，0 = 禁能
|
||
* 限定条件：芯片已初始化
|
||
* 函数说明：参考手册5.37节CMD_PING_ENABLE，默认禁能
|
||
*/
|
||
void ch395f_ping_enable(uint8_t enable) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送PING使能命令 */
|
||
ch395f_write_cmd(CH395F_CMD_PING_ENABLE);
|
||
|
||
/* 发送使能标志 */
|
||
ch395f_write_data(enable);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：使能/禁能DHCP
|
||
* 入口参数：enable - 使能标志 uint8_t 1 = 使能，0 = 禁能
|
||
* 限定条件：芯片已初始化
|
||
*/
|
||
void ch395f_set_dhcp(uint8_t enable) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送DHCP使能命令 */
|
||
ch395f_write_cmd(CH395F_CMD_DHCP_ENABLE);
|
||
|
||
/* 发送使能/禁能参数 */
|
||
ch395f_write_data(enable);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：获取DHCP状态
|
||
* 返回值：0 = 成功，非零 = 错误/超时 uint8_t
|
||
* 限定条件：芯片已初始化且DHCP已使能
|
||
*/
|
||
uint8_t ch395f_get_dhcp_status(void) {
|
||
uint8_t status;
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送读取DHCP状态命令 */
|
||
ch395f_write_cmd(CH395F_CMD_GET_DHCP_STATUS);
|
||
|
||
/* 读取DHCP状态 */
|
||
status = ch395f_read_data();
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
|
||
return status;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置Socket协议类型
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 3
|
||
* proto - 协议类型 uint8_t CH395F_PROTO_TYPE_xxx
|
||
* 限定条件：Socket必须处于关闭状态
|
||
*/
|
||
void ch395f_set_proto_type(uint8_t sock, uint8_t proto) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置协议类型命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_PROTO_TYPE_SN);
|
||
|
||
/* 发送Socket索引 */
|
||
ch395f_write_data(sock);
|
||
|
||
/* 发送协议类型 */
|
||
ch395f_write_data(proto);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置Socket目标IP地址
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 3
|
||
* p_ip - 4字节目标IP指针 uint8_t*
|
||
* 限定条件：p_ip不可为NULL
|
||
*/
|
||
void ch395f_set_des_ip(uint8_t sock, uint8_t *p_ip) {
|
||
uint8_t i;
|
||
|
||
/* 检查输入参数合法性 */
|
||
if (p_ip == NULL) {
|
||
return;
|
||
}
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置目标IP命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_IP_ADDR_SN);
|
||
|
||
/* 发送Socket索引 */
|
||
ch395f_write_data(sock);
|
||
|
||
/* 逐字节发送目标IP地址 */
|
||
for (i = 0; i < 4; i++) {
|
||
ch395f_write_data(p_ip[i]);
|
||
}
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置Socket目标端口（小端格式）
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 3
|
||
* port - 目标端口号 uint16_t
|
||
*/
|
||
void ch395f_set_des_port(uint8_t sock, uint16_t port) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置目标端口命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_DES_PORT_SN);
|
||
|
||
/* 发送Socket索引 */
|
||
ch395f_write_data(sock);
|
||
|
||
/* 发送端口低字节 */
|
||
ch395f_write_data(port & 0xFFU);
|
||
|
||
/* 发送端口高字节 */
|
||
ch395f_write_data((port >> 8) & 0xFFU);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置Socket源端口（小端格式）
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 3
|
||
* port - 源端口号 uint16_t
|
||
*/
|
||
void ch395f_set_sour_port(uint8_t sock, uint16_t port) {
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送设置源端口命令 */
|
||
ch395f_write_cmd(CH395F_CMD_SET_SOUR_PORT_SN);
|
||
|
||
/* 发送Socket索引 */
|
||
ch395f_write_data(sock);
|
||
|
||
/* 发送端口低字节 */
|
||
ch395f_write_data(port & 0xFFU);
|
||
|
||
/* 发送端口高字节 */
|
||
ch395f_write_data((port >> 8) & 0xFFU);
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：打开Socket
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* 返回值：命令执行状态（CH395F_ERR_SUCCESS = 成功） uint8_t
|
||
* 限定条件：协议类型、目标IP和端口必须已设置
|
||
*/
|
||
uint8_t ch395f_open_socket(uint8_t sock) {
|
||
ch395f_spi_begin();
|
||
ch395f_write_cmd(CH395F_CMD_OPEN_SOCKET_SN);
|
||
ch395f_write_data(sock);
|
||
ch395f_spi_end();
|
||
|
||
return ch395f_poll_cmd_status(4000U);
|
||
}
|
||
|
||
/*
|
||
* 函数功能：关闭Socket
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* 返回值：命令执行状态（CH395F_ERR_SUCCESS = 成功） uint8_t
|
||
* 限定条件：Socket必须已打开
|
||
*/
|
||
uint8_t ch395f_close_socket(uint8_t sock) {
|
||
ch395f_spi_begin();
|
||
ch395f_write_cmd(CH395F_CMD_CLOSE_SOCKET_SN);
|
||
ch395f_write_data(sock);
|
||
ch395f_spi_end();
|
||
|
||
return ch395f_poll_cmd_status(4000U);
|
||
}
|
||
|
||
/*
|
||
* 函数功能：启动TCP监听模式
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* 返回值：命令执行状态（CH395F_ERR_SUCCESS = 成功） uint8_t
|
||
* 限定条件：Socket必须已打开且协议类型为TCP
|
||
*/
|
||
uint8_t ch395f_tcp_listen(uint8_t sock) {
|
||
ch395f_spi_begin();
|
||
ch395f_write_cmd(CH395F_CMD_TCP_LISTEN_SN);
|
||
ch395f_write_data(sock);
|
||
ch395f_spi_end();
|
||
|
||
return ch395f_poll_cmd_status(4000U);
|
||
}
|
||
|
||
/*
|
||
* 函数功能：发起TCP连接
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* 返回值：命令执行状态（CH395F_ERR_SUCCESS = 成功） uint8_t
|
||
* 限定条件：Socket必须已打开且协议类型为TCP
|
||
*/
|
||
uint8_t ch395f_tcp_connect(uint8_t sock) {
|
||
ch395f_spi_begin();
|
||
ch395f_write_cmd(CH395F_CMD_TCP_CONNECT_SN);
|
||
ch395f_write_data(sock);
|
||
ch395f_spi_end();
|
||
|
||
return ch395f_poll_cmd_status(4000U);
|
||
}
|
||
|
||
/*
|
||
* 函数功能：断开TCP连接
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* 返回值：命令执行状态（CH395F_ERR_SUCCESS = 成功） uint8_t
|
||
* 限定条件：TCP连接必须已建立
|
||
*/
|
||
uint8_t ch395f_tcp_disconnect(uint8_t sock) {
|
||
ch395f_spi_begin();
|
||
ch395f_write_cmd(CH395F_CMD_TCP_DISCONNECT_SN);
|
||
ch395f_write_data(sock);
|
||
ch395f_spi_end();
|
||
|
||
return ch395f_poll_cmd_status(4000U);
|
||
}
|
||
|
||
/*
|
||
* 函数功能：向Socket发送缓冲区写入数据（DMA批量传输）
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 3
|
||
* p_data - 数据指针 uint8_t*
|
||
* len - 数据长度 uint16_t
|
||
* 限定条件：1. p_data不可为NULL
|
||
* 2. 数据长度必须大于0
|
||
* 3. TCP必须已连接或UDP已打开
|
||
* 函数说明：1. 将命令头和数据打包到DMA发送缓冲区
|
||
* 2. 一次性SPI DMA传输完成
|
||
* 3. 数据同步屏障确保memcpy写入对DMA可见
|
||
*/
|
||
void ch395f_write_send_buf(uint8_t sock, uint8_t *p_data, uint16_t len) {
|
||
uint16_t total;
|
||
|
||
/* 检查输入参数合法性 */
|
||
if (p_data == NULL) {
|
||
return;
|
||
}
|
||
|
||
/* 计算总长度：1字节命令 + 1字节Socket + 2字节长度 + 数据 */
|
||
total = 4U + len;
|
||
if (total > CH395F_DMA_BUF_SIZE) {
|
||
return;
|
||
}
|
||
|
||
/* 打包命令头到DMA发送缓冲区 */
|
||
s_spi2_dma_tx_buf[0] = CH395F_CMD_WRITE_SEND_BUF_SN;
|
||
s_spi2_dma_tx_buf[1] = sock;
|
||
s_spi2_dma_tx_buf[2] = len & 0xFFU;
|
||
s_spi2_dma_tx_buf[3] = (len >> 8) & 0xFFU;
|
||
|
||
/* 拷贝用户数据到DMA发送缓冲区 */
|
||
memcpy(&s_spi2_dma_tx_buf[4], p_data, len);
|
||
|
||
/* 数据同步屏障：确保memcpy写入对DMA可见 */
|
||
__DSB();
|
||
|
||
/* CS低 → DMA批量传输 → CS高 */
|
||
ch395f_spi_begin();
|
||
ch395f_spi_dma_transfer(total);
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：从Socket接收缓冲区读取数据（DMA批量传输）
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 3
|
||
* p_data - 输出缓冲区指针 uint8_t*
|
||
* len - 待读取数据长度 uint16_t
|
||
* 限定条件：1. p_data不可为NULL
|
||
* 2. 数据长度必须大于0
|
||
* 3. 接收缓冲区中必须有数据
|
||
* 函数说明：1. 命令头打包到发送缓冲区（数据部分填充0xFF作为时钟源）
|
||
* 2. 一次性SPI DMA全双工传输
|
||
* 3. 有效数据从接收缓冲区偏移4处拷贝到用户缓冲区
|
||
*/
|
||
void ch395f_read_recv_buf(uint8_t sock, uint8_t *p_data, uint16_t len) {
|
||
uint16_t total;
|
||
|
||
/* 检查输入参数合法性 */
|
||
if (p_data == NULL) {
|
||
return;
|
||
}
|
||
|
||
/* 计算总长度：1字节命令 + 1字节Socket + 2字节长度 + 数据 */
|
||
total = 4U + len;
|
||
if (total > CH395F_DMA_BUF_SIZE) {
|
||
return;
|
||
}
|
||
|
||
/* 打包命令头到DMA发送缓冲区 */
|
||
s_spi2_dma_tx_buf[0] = CH395F_CMD_READ_RECV_BUF_SN;
|
||
s_spi2_dma_tx_buf[1] = sock;
|
||
s_spi2_dma_tx_buf[2] = len & 0xFFU;
|
||
s_spi2_dma_tx_buf[3] = (len >> 8) & 0xFFU;
|
||
|
||
/* 数据部分填充0xFF（作为SPI时钟源） */
|
||
memset(&s_spi2_dma_tx_buf[4], 0xFFU, len);
|
||
|
||
/* CS低 → DMA全双工传输（发送命令头 + 接收数据） → CS高 */
|
||
ch395f_spi_begin();
|
||
ch395f_spi_dma_transfer(total);
|
||
ch395f_spi_end();
|
||
|
||
/* 从DMA接收缓冲区偏移4处拷贝有效数据到用户缓冲区 */
|
||
memcpy(p_data, &s_spi2_dma_rx_buf[4], len);
|
||
}
|
||
|
||
/*
|
||
* 函数功能：获取Socket接收缓冲区中数据长度
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 3
|
||
* 返回值：接收数据长度 uint16_t
|
||
* 限定条件：Socket必须已打开
|
||
*/
|
||
uint16_t ch395f_get_recv_len(uint8_t sock) {
|
||
uint16_t recv_len;
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送获取接收长度命令 */
|
||
ch395f_write_cmd(CH395F_CMD_GET_RECV_LEN_SN);
|
||
|
||
/* 发送Socket索引 */
|
||
ch395f_write_data(sock);
|
||
|
||
/* 读取长度低字节 */
|
||
recv_len = ch395f_read_data();
|
||
|
||
/* 读取长度高字节并组合 */
|
||
recv_len |= (uint16_t)ch395f_read_data() << 8;
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
|
||
return recv_len;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：获取全局中断状态（2字节版，支持Socket 0~7）
|
||
* 返回值：中断状态 uint16_t（低字节 = Socket 0~3 + PHY/DHCP，
|
||
* 高字节 = Socket 4~7 + DHCPv6）
|
||
* 限定条件：芯片已初始化
|
||
*/
|
||
uint16_t ch395f_get_glob_int_status_all(void) {
|
||
uint16_t status;
|
||
|
||
ch395f_spi_begin();
|
||
ch395f_write_cmd(CH395F_CMD_GET_GLOB_INT_STATUS_ALL);
|
||
status = (uint16_t)ch395f_read_data();
|
||
status |= ((uint16_t)ch395f_read_data() << 8U);
|
||
ch395f_spi_end();
|
||
|
||
return status;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：获取Socket中断状态
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* 返回值：Socket中断状态字节 uint8_t
|
||
* 限定条件：芯片已初始化
|
||
*/
|
||
uint8_t ch395f_get_sock_int_status(uint8_t sock) {
|
||
uint8_t status;
|
||
|
||
/* 启动SPI事务 */
|
||
ch395f_spi_begin();
|
||
|
||
/* 发送读取Socket中断状态命令 */
|
||
ch395f_write_cmd(CH395F_CMD_GET_INT_STATUS_SN);
|
||
|
||
/* 发送Socket索引 */
|
||
ch395f_write_data(sock);
|
||
|
||
/* 读取中断状态 */
|
||
status = ch395f_read_data();
|
||
|
||
/* 结束SPI事务 */
|
||
ch395f_spi_end();
|
||
|
||
return status;
|
||
}
|
||
|
||
/*
|
||
* 函数功能：获取Socket状态（2字节输出）
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* p_status - 2字节输出缓冲区指针 uint8_t*
|
||
* [0] = Socket状态, [1] = TCP状态
|
||
* 限定条件：芯片已初始化
|
||
* 函数说明：Socket状态: 00H=CLOSED, 05H=OPEN
|
||
* TCP状态: 00H=CLOSED, 01H=LISTEN, 02H=SYN_SENT,
|
||
* 03H=SYN_RCVD, 04H=ESTABLISHED
|
||
*/
|
||
void ch395f_get_socket_status(uint8_t sock, uint8_t *p_status) {
|
||
ch395f_spi_begin();
|
||
ch395f_write_cmd(CH395F_CMD_GET_SOCKET_STATUS_SN);
|
||
ch395f_write_data(sock);
|
||
p_status[0] = ch395f_read_data();
|
||
p_status[1] = ch395f_read_data();
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置ARP重传参数
|
||
* 入口参数：period_100ms - ARP重传周期（单位：100ms，默认：10 = 1s） uint8_t 0 - 255
|
||
* cnt - ARP重传次数（默认：3） uint8_t 0 - 255
|
||
* 限定条件：应在ch395f_init()之后调用
|
||
* 函数说明：最大周期约25.5秒，255表示无限重传
|
||
*/
|
||
void ch395f_set_arp(uint8_t period_100ms, uint8_t cnt) {
|
||
ch395f_spi_begin();
|
||
ch395f_write_cmd(CH395F_CMD_SET_ARP);
|
||
ch395f_write_data(period_100ms);
|
||
ch395f_write_data(cnt);
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：设置Socket的TTL值
|
||
* 入口参数：sock - Socket索引 uint8_t 0 - 7
|
||
* ttl - TTL值 uint8_t 最大128
|
||
* 限定条件：Socket必须已打开，TCP Server模式下不生效
|
||
*/
|
||
void ch395f_set_ttl(uint8_t sock, uint8_t ttl) {
|
||
ch395f_spi_begin();
|
||
ch395f_write_cmd(CH395F_CMD_SET_TTL);
|
||
ch395f_write_data(sock);
|
||
ch395f_write_data(ttl);
|
||
ch395f_spi_end();
|
||
}
|
||
|
||
/*
|
||
* 函数功能：获取不可达信息（用于调试连接失败原因）
|
||
* 出口参数：p_buf - 8字节输出缓冲区指针（类型+协议+端口+IP） uint8_t*
|
||
* 限定条件：收到GINT_STAT_UNREACH中断后调用
|
||
*/
|
||
void ch395f_get_unreach_info(uint8_t *p_buf) {
|
||
uint8_t i = 0;
|
||
|
||
ch395f_spi_begin();
|
||
ch395f_write_cmd(CH395F_CMD_GET_UNREACH_IPPT);
|
||
for (i = 0; i < 8; i++) {
|
||
p_buf[i] = ch395f_read_data();
|
||
}
|
||
ch395f_spi_end();
|
||
}
|