75 lines
3.8 KiB
Markdown
75 lines
3.8 KiB
Markdown
---
|
||
description: Build → flash (download) → capture USART1 debug log → verify boot/test markers → iterate. The full automated test loop for the STM32F4-Base target.
|
||
agent: build
|
||
---
|
||
|
||
Run the full automated test loop: **build → download → capture serial debug → verify markers → report/iterate**.
|
||
|
||
Prerequisites (checked in step 0):
|
||
- `serial-mcp-server` CLI installed at `%LOCALAPPDATA%\serial-mcp-server\serial-mcp-server.exe` (Adancurusul/serial-mcp-server, v0.3.0).
|
||
- ST-Link probe connected; target powered. The USB-serial (CH340) may stay idle while flashing — ST-Link download does not conflict with the serial port.
|
||
|
||
## Procedure
|
||
|
||
### Step 0 — Pre-flight: serial-mcp-server binary + port
|
||
|
||
Verify the capture binary and target port exist:
|
||
|
||
```powershell
|
||
Test-Path "$env:LOCALAPPDATA\serial-mcp-server\serial-mcp-server.exe"
|
||
& "$env:LOCALAPPDATA\serial-mcp-server\serial-mcp-server.exe" list-ports --json
|
||
```
|
||
|
||
Read `.opencode/serial_config.json` for the authoritative `portName` (COM6) and match it in the list. If the binary is missing, build it from source (see `docs/测试说明/serial-mcp-server_串口调试.md`).
|
||
|
||
### Step 1 — Build verify
|
||
|
||
Run the build script (repo-relative; the repo root is the working directory):
|
||
|
||
```powershell
|
||
& "MDK-ARM\build.bat"
|
||
```
|
||
|
||
Interpretation (per AGENTS.md): exit code 0 = PASS (0 errors, 0 warnings). 1/2+ = FAIL. If it fails, read `MDK-ARM/build_log.txt`, fix, and rerun `@build` until exit code 0 **before** touching the hardware.
|
||
|
||
### Step 2 — Flash + capture boot log (one orchestrated call)
|
||
|
||
Use `test/run_boot_test.ps1` which starts the capture (waits for first byte),
|
||
then flashes, then collects and verifies — all in one call so the capture never
|
||
times out before flashing:
|
||
|
||
```powershell
|
||
powershell -ExecutionPolicy Bypass -File "test\run_boot_test.ps1" `
|
||
-Port COM6 -BaudRate 115200 `
|
||
-DurationMs 30000 -InitialTimeoutMs 90000 -IdleTimeoutMs 8000 -MaxBytes 65536 `
|
||
-FlashCmd "MDK-ARM\download.bat" `
|
||
-Required "App init OK;Network Init;net init: OK" `
|
||
-Forbidden "FAIL;ERROR;HardFault" `
|
||
-OutDir "C:\Users\16241\AppData\Local\Temp\opencode"
|
||
```
|
||
|
||
Exit codes: **0 = PASS**, 1 = FAIL (marker miss / forbidden hit), 2 = capture/flash/parse error.
|
||
|
||
### Step 3 — Iterate
|
||
|
||
- **PASS** → report the verdict and which markers matched; done.
|
||
- **FAIL** → the `[MISS]`/`[HIT]` lines + the log tail show what went wrong. Fix the code, then loop again from **Step 1**. Do not skip the build step.
|
||
|
||
## Alternative: manual MCP capture (interactive debug)
|
||
|
||
For interactive command/response (not boot-log capture):
|
||
|
||
1. `serial_list_ports` → match `portName` from `.opencode/serial_config.json` (COM6).
|
||
2. `serial_open` (port=COM6, baud_rate=115200) → note the returned `connection_id`.
|
||
3. `serial_write` / `serial_read` (connection_id, timeout_ms) for command-response.
|
||
4. `serial_close` to release the port.
|
||
|
||
## Notes
|
||
|
||
- **串口端口**：以 `.opencode/serial_config.json` 为准（本机为 COM6）。每次连接前先读它。
|
||
- **⚠️ 无历史缓冲**：serial-mcp-server 的 `read` 只能读调用后的字节。抓开机日志必须走 `run_boot_test.ps1`（先采集等 first-byte → 再烧录触发）。
|
||
- **⚠️ EOF 陷阱**：COM 刚释放立即重开会报 `UnexpectedEof`（tokio-serial 读 0 字节）。`serial_capture.ps1` 内置自动重试；别裸跑 CLI capture。
|
||
- **参数**：`IdleTimeoutMs` 需 ≥ boot 自然静默间隙（本机 ~3-4s，用 8000）；`InitialTimeoutMs` 需覆盖编译+烧录耗时（用 90000）。
|
||
- UI (LVGL) task `ui_task` 已有 `UI port init: OK` / `UI menu init: OK` 打印，可用 `-Required "UI port init: OK;UI menu init: OK"` 自动回归 UI 初始化。
|
||
- Full capture/analysis details: `docs/测试说明/serial-mcp-server_串口调试.md` and `docs/测试说明/自动化测试流程.md`.
|